Konica Minolta bizhub 4050 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 56

background image

2.2

Replacing consumables

2

[Maintenance/Troubleshooting]

2-3

2.2

Replacing consumables

NOTICE

A failure, which was caused because you did not follow the procedures described in this user's guide, is not
included in the warranty.

2.2.1

Replacing a Toner Cartridge

Handling a Toner Cartridge

When handling a

Toner Cartridge

, be careful of the following.

-

When handling a

Toner Cartridge

, take care not to spill toner on this machine or your hand.

-

Replace a

Toner Cartridge

with an unused product. If a toner cartridge is replaced with a used one,

the message window may not to be cleared or the toner level may not be displayed accurately.

-

Do not forcibly open the

Toner Cartridge

. If toner has leaked, avoid toner inhaling or skin contact as

much as possible.

-

If your clothes or hand has been stained with toner, wash it off with soap and water.

-

If you have inhaled toner, move to a fresh air place, then gargle well with a large amount of water. If you
have had a symptom such as a cough, see your doctor.

-

If any toner enters your eyes, immediately wash them with running water for 15 minutes or more. If pain
persists, see your doctor.

-

If you have drunk toner, wash your mouth out well, then drink one or two glasses of water. See your
doctor, if necessary.

-

Keep

Toner Cartridge

out of reach of babies and children.

Storing Toner Cartridges

Store

Toner Cartridge

as shown below.

-

Do not open the protection bag before installing a

Toner Cartridge

.

-

Store Toner Cartridges in a cold dark place, away from direct sunlight.

-

Store Toner Cartridges in a location in which the temperature is 95°F (35°C) or less and the humidity is
80% or less with no dew condensation. If a

Toner Cartridge

is moved from a cold place to a warm

place with high humidity, a dew may form. which may affect printing quality. Before using a

Toner Car-

tridge

, leave it for approximately one hour to adjust to the ambient environment.

-

Keep Toner Cartridges horizontal. Do not place a

Toner Cartridge

in the reverse direction from that

specified. Doing so may cause toner in a

Toner Cartridge

to become hard or uneven.

-

Do not touch salty air or corrosive gases such as aerosol.

Tips

Guidance for recovering used

Toner Cartridge

-

Put the used

Toner Cartridge

in a bag, place the bag in the box in which the Toner Cartridge was in-

cluded at the time of purchase, then send the box to us. Securely seal the bag and box with tape, being
careful of the toner in the

Toner Cartridge

. The recovered

Toner Cartridge

and

Imaging Unit

are re-

cycled.

Replacement procedure

NOTICE

Do not use a recycle Toner Cartridge other than our genuine product. A failure or problem that affects printing
quality and that was caused due to use of a recycled Toner Cartridge is not covered by the warranty. Such a
failure or problem is not subject to technical support.

«
...
9
10
11
12
13
...
»

Содержание bizhub 4050

























































Отзывы:

Нет отзывов

Похожие инструкции для bizhub 4050

Бренд: Oki Страницы: 6

Бренд: Oki Страницы: 44

Бренд: Oki Страницы: 13

Бренд: Oki Страницы: 20

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 28

Бренд: Samsung Страницы: 82

Бренд: Samsung Страницы: 2

DocuPrint C3055 DX

Бренд: Xerox Страницы: 20

Бренд: Olivetti Страницы: 74

WorkCentre Pro 90

Бренд: Xerox Страницы: 36

Бренд: AstroJet Страницы: 32

VersaLink Series

Бренд: Xerox Страницы: 185

Бренд: Xerox Страницы: 150

Бренд: Unytouch Страницы: 12

Бренд: Oki Страницы: 56

Бренд: Citizen Страницы: 88

Бренд: Ricoh Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды