Kongsberg RV-2 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 66

background image

Maintenance manual

KONGSBERG PROPRIETARY.

This document and its accompanying elements contain KONGSBERG

information which is proprietary and confidential. Any disclosure, copying, distribution or use is prohibited if not
otherwise explicitly agreed with KONGSBERG in writing. Any authorized reproduction, in whole or in part, must
include this legend. ©2022 KONGSBERG - All rights reserved.

P a g e

41 |

66

11.13

Function Test of Alarm System

Please follow below procedure in order to complete a function test of the alarms on the alarm
system installed.

Note!

There is a 5 sec delay in the alarm system. If any alarm is present in the alarm system, the auto
start will not work, so please check all alarms on the alarm panel before you test the next alarm.

Alarm test

Overload

Test Push Button

Phase failure

Remove fuse F17

Power failure

Turn of main switch

Power control failure

Turn selector switch to position 2

Low oil level

Disconnect sensor from PP

Hydraulic lock

Keep selector switch in remote and operate the Steering Gear locally

Clogged filter

Disconnect sensor from PP

High oil temp

Disconnect sensor from PP

Low oil pressure

Close handle before starting the pump

Power failure aux. steering

Remove fuse F41-42-43-44

Overload alarm:

Push the test button on the overload relay in motor controller. The stand-by pump should start if not
already running.

Phase failure alarm:

Remove one of the fuses supplying the phase failure monitoring relay in the motor controller
cabinet, the stand-by pump should start if not already running.

Power failure:

Turn of main switch S1 in the motor controller or the circuit breaker from switch board. The stand-by
pump should start if not already running.

Power control failure alarm:

Set the S2 selector switch located on the outside of the motor controller cabinet to

local

control or

stop

, the stand-by pump should start if not already running.

Low oil level alarm:

Disconnect the connection plug on top of the expansion tank.
The stand-by pump should start if not already running.

Hydraulic lock alarm

:

Activate manual solenoid in either direction while the motor controller is in remote control. Keep
activated for more than 5 seconds.
The stand-by pump should start if not already running.

«
...
39
40
41
42
43
...
»

Содержание RV-2



































































Отзывы:

Нет отзывов

Похожие инструкции для RV-2

Бренд: RASHA PROFESSIONAL Страницы: 11

Бренд: MADRIX Страницы: 24

Бренд: MADRIX Страницы: 28

Бренд: Mandam Страницы: 9

Бренд: Datavideo Страницы: 48

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 3

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 8

Бренд: Datavideo Страницы: 10

Бренд: GE Страницы: 212

Бренд: Gaspardo Страницы: 16

Бренд: Gastrodomus Страницы: 4

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Gastrodomus Страницы: 39

Бренд: Harken Страницы: 4

Бренд: Harken Страницы: 2

TERRA FORCE BOOM

Бренд: Hardi Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды