Kongsberg K-Sync Скачать руководство пользователя страница 34

Страница: 34 / 72

342741/B

The following applies if the echo sounder provides Ready to

transmit

as well as

Transmitting

signals:

Figure 7

Signal timing scheme

Echo sounder is ready to transmit.

Ready to transmit (RTT) signal is active.

K-Sync triggers echo sounder.

Trigger pulse is generated.

Echo sounder acknowledges the transmit.

Transmitting

goes high.

Transmit is indicated in the trigger plot by the grey spike.

Ping delay, i.e. time from trigger to actual transmit.

Pulse width of trigger pulse generated by K-Sync.

Ready to transmit (RTT) goes high again, i.e. the ping cycle is complete.

The state plot turns dark again.

The ping cycle.

For echo sounders that do not have a transmitting signal, the Synchronizing Unit will
not be able to verify that the transmit occurred. Likewise, if the ready to transmit is not

KONGSBERG K-Sync Installation manual

Содержание K-Sync









































































Результаты поиска

Содержание K-Sync

Отзывы:

Похожие инструкции для K-Sync

Бренды по названию

Популярные бренды

Kongsberg K-Sync, Руководство по установке

Результаты поиска

Содержание K-Sync

Отзывы:

Похожие инструкции для K-Sync

Бренды по названию

Популярные бренды