manualshive.com logo in svg

komodo KDGASPATHTRA, Руководство пользователя, Страница: 11 / 11

Поделиться
Скачать
komodo KDGASPATHTRA Скачать руководство пользователя страница 11

Lighting Instructions

Warning: white smoke may appear around the radiant head during the first minutes of 

the initial firing.

Step 1

Ensure the control knob is off. Slowly open the gas cylinder valve.

Step 2

Push the control knob in and turn anti-clockwise to 'HIGH' whilst simultaneously 

pushing the ignitor button several times.

Step 3

Check for a flame at the burner. If the burner does not light immediately, turn the 

control knob to 'OFF' and try the instructions again from the start.  Allow 30 seconds 

between ignition attempts to allow the gas to dissipate. Several attempts may be 

necessary.

Failure to follow this procedure may result in flames rolling out beyond the emitter grid.

Step 4

With the burner alight, keep the control knob depressed for 15 seconds.

Step 5

For minimum heat, push the control knob in and turn it to 'LOW'.

Step 6

To turn the heater off, turn the control knob to 'OFF'.

Troubleshooting

Problem

Possible Causes

Main burner won't light

•

No gas

•

Low gas pressure

•

Blockage in hose or orifice

•

Manual valve not in the 'LOW' or 'HIGH' position

Note: if the heater cannot be adjusted to perform correctly, it should not be used until 

serviced or repaired.

Warning: improper installation, adjustment, alteration, service or maintenance can cause

injury or property damage. Any modifications or adjustments made to the product 

without prior authority from Kogan.com will void any warranty claims.

Read the installation, operation and maintenance instructions thoroughly before 

installing or servicing this equipment.

11

Содержание KDGASPATHTRA












Отзывы:

Нет отзывов