komodo KDGASPATHTRA Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 11

komodo KDGASPATHTRA Скачать руководство пользователя страница 10

Reflector Assembly

1. Place the 3 parts of the reflector segments so they are overlapping with each

other, then attach with 3 screws, washers and nuts.

2. Place the round part of the reflector over the 3 segments, then attach with 6

screws, washers and nuts.

Usage

Test Firing Heater

Test fire the heater following the lighting instructions on the heater post. Leak test all

gas connections with soapy water. Soap bubbles indicate gas leakage. DO NOT use a

match to test for gas leaks.

WARNING: White smoke may appear around the radiant head during the first minute of

the initial firing. This is completely normal.

Abnormal Operation

Any of the following are considered to be abnormal operations:

•

Yellow tips on the burner flames.

•

Fumes or strong odours.

•

Soot build-up.

•

A gas valve that is difficult to turn on or gets stuck.

If the heat operates abnormally, DO NOT use the heater. Contact the Kogan.com

customer support team.

10

«
...
8
9
10
11
»

Содержание KDGASPATHTRA












Отзывы:

Нет отзывов