Komfovent VERSO Pro P Скачать руководство пользователя страница 38

Страница: 38 / 52

UAB KOMFOVENT we reserve the right to make changes without prior notice

V-C5.1_21-01

6.5.1.5. Filter status

It is possible to monitor the pollution level of filters and to calibrate clean

filters.

It is recommended to perform the initial calibration of

filters after the first start of the unit. When filters are re-

placed during operation, it is recommended to perform

the clean filter calibration.

6.5.1.6. Inspection lightning

In this menu item you can switch on/off the light during the unit inspec-

tion, for instance, when replacing filters. The option appears on the panel only

if the air handling unit has been pre-ordered with built-in lighting.

Clean filters calibration

Filter status

Outdoor air filter impurity

55%

Extract air filter impurity

60%

6.5.2. Functions

In this menu item, the user can activate and

set additional unit functions.

blank box: function is not activated

gray box: function is activated, but currently not op-

erating

blue box: currently operating function

Functions

1 / 2

Air quality

control

Operation on

demand

Outdoor compen

sated ventilation

Summer night

cooling

Minimum tempera-

ture control

Functions

Settings

Overview

Scheduling

6.5.2.1. Air quality control

Air quality control is designed according to:

•

sensor

[0...2000 ppm];

•

air quality sensor VOCq [0...100 %];

•

air pollution sensor VOCp [0...100 %];

•

relative humidity sensor [0...100 %];

•

temperature sensor [0...50 ºC].

Depending on the type of the selected sensor, the value of the air qual-

ity function to be maintained is set, and the air handling unit intensity will

be adjusted according to that value. Ventilation intensity will be increased

automatically in the case of deviation from the set value and decreased again

when it is approached. For example, if the unit is designed with the CO

main-

tenance function and is equipped with a CO

sensor, after setting value 800

ppm, this set CO

level will be maintained by adjusting ventilation intensity,

i.e. ventilation intensity will be increased if the CO

level grows and will be

decreased when it returns to the previous condition.

The function of air quality operates only if no other below func-

tion is active at the same time:

• summer night cooling;

• min. temperature control;

• outdoor compensated ventilation.

Factory setting.

Reset settings

Enable

Setpoint 1

1000 ppm

Setpoint 2

880 ppm

Mode 1

COMFORT 1

Mode 2

COMFORT 2

Air quality control

Содержание VERSO Pro P





















































Результаты поиска

Содержание VERSO Pro P

Отзывы:

Бренды по названию

Популярные бренды

Komfovent VERSO Pro P, Инструкция по установке и обслуживанию

Результаты поиска

Содержание VERSO Pro P

Отзывы:

Бренды по названию

Популярные бренды