Komfovent Domekt CF 250 F Скачать руководство пользователя

Страница: 24 / 32

UAB KOMFOVENT we reserve the right to make changes without prior notice

D_20-07

4.2. Heating coil connection

Pipe work should be connected in accordance with good engineering practice. All pipe work must be

adequatelysupported to ensure that no additional load is stressing the unit. Mounting the pipes on the heating

coil, tight the pipes with spanners. As shown in 19 Picture.

Fitting Pipes Connection

19 a Picture

Sensors Installation

19 b Picture

The pipe work should be done in order to ensure the space for maintenance and service work. When carrying

out the installation of heater pipes, make sure that hot water supply is completely disconnected. Before start-up of

the air handling unit, the heater system should be filled in with water. Glycol is used in the air handling units with

coil heat exchanger. Never pour glycol down a drain; collect it in a receptacle and leave it at a recycling centre or

the like. Glycol is highly dangerous to consume and can cause fatal poisoning or damage the kidneys. Contact a

doctor! Avoid breathing glycol vapour in confined spaces. If you get glycol in your eyes, fush them thoroughly with

water (for about 5 minutes).

When operating air handling unit in the temperatures lower than 0 °C, it

is necessary to use glycol additionally or assure the reversible heating

agent temperature more than 25 °C.

Pipework package

must include circulation pump, which circulates

heating/cooling medium through the coil (smaller circuit) and 3-way

mixing valve with modulated actuator. In cases if 2-way valve is used,

additionally it must be installed non-return valves to ensure continuous

circulation around smaller circuit. PPU must be installed as close to the

water coil as possible.

It is important to maintain air heaters and coolers cleanliness; that is to

change filters installed in the air handling unit on time. If the air heater or

cooler gets dirty, to perform periodical cleaning.

If water heater build in.

It is recommended to use PPU made by Komfovent.

Содержание Domekt CF 250 F

































Результаты поиска

Содержание Domekt CF 250 F

Отзывы:

Похожие инструкции для Domekt CF 250 F

Бренды по названию

Популярные бренды

Komfovent Domekt CF 250 F, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Domekt CF 250 F

Отзывы:

Похожие инструкции для Domekt CF 250 F

Бренды по названию

Популярные бренды