Komatsu A87001 Скачать руководство пользователя страница 38

Страница: 38 / 51

FOREWORD

ELECTRIC WIRE CODE

00-26

PC200/220LL-8

How To Read Electric Wire Code

★

The information about the wires unique to each machine model is described in Troubleshooting section, Relational

information of troubleshooting.

In the electric circuit diagram, the material, thickness, and color of each electric wire are indicated by symbols. The electric
wire code is helpful in understanding the electric circuit diagram.

Type, Symbol, And Material

AV and AVS are different in only thickness and outside diameter of the cover. AEX is similar to AV in thickness and

outside diameter of AEX and different from AV and AVS in material of the cover.

Example:

AEX

0.85

- - - Indicates blue, heat-resistant, low-voltage wire for automobile, having nominal No. of

0.85

Indicates color of wire by color code.

Color codes are shown in Table 3.

Indicates size of wire by nominal No.

Size (Nominal No.) is shown in Table 2.

Indicates type of wire by symbol.

Type, symbol, and material of wire are shown in Table 1.

(Since AV and AVS are classified by size (nominal No.), they are not indicated.)

(Table 1)

Type

Symbol

Material

Using

temperature

range °C (°F)

Example of use

Low-voltage

wire for

automobile

Conductor

Annealed copper for electric

appliance

–30 to +60

(-22 to +140)

General wiring

(Nominal No. 5 and above)

Insulator

Soft polyvinyl chloride

Thin-cover

low-voltage

wire for

automobile

AVS

Conductor

Annealed copper for electric

appliance

General wiring

(Nominal No. 3 and below)

Insulator

Soft polyvinyl chloride

Heat-resistant

low-voltage

wire for

automobile

AEX

Conductor

Annealed copper for electric

appliance

–50 to +110

(-58 to +230)

General wiring in extremely cold

district, wiring at high-temperature

place

Insulator

Heat-resistant crosslinked

polyethylene

Содержание A87001




















































Результаты поиска

Содержание A87001

Отзывы:

Похожие инструкции для A87001

Бренды по названию

Популярные бренды

Komatsu A87001, Руководство по ремонту

Результаты поиска

Содержание A87001

Отзывы:

Похожие инструкции для A87001

Бренды по названию

Популярные бренды