Komatsu A87001 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 51

background image

FOREWORD

EXPLANATION OF MAINTENANCE STANDARD TERMS

PC200/220LL-8

00-21

b

12

4.

Repair Limit And Allowable Value

•

The size of a part changes because of wear and deformation while it is used. The limit of changed size is called the
“repair limit”.

•

If a part is worn to the repair limit must be replaced or repaired.

•

The performance and function of a product lowers while it is used. A value below which the product can be used
without causing a problem is called the “allowable value”.

•

If a product is worn to the allowable value, it must be checked or repaired. Since the permissible value is estimated
from various tests or experiences in most cases, however, it must be judged after considering the operating condition
and customer's requirement.

5.

Clearance Limit

•

Parts can be used until the clearance between them is increased to a certain limit. The limit at which those parts

cannot be used is called the “clearance limit”.

•

If the clearance between the parts exceeds the clearance limit, they must be replaced or repaired.

6.

Interference Limit

•

The allowable maximum interference between the hole of a part and the shaft of another part to be assembled is called
the “interference limit”.

•

The interference limit shows the repair limit of the part of smaller tolerance.

•

If the interference between the parts exceeds the interference limit, they must be replaced or repaired.

«
...
31
32
33
34
35
...
»

Содержание A87001




















































Отзывы:

Нет отзывов

Похожие инструкции для A87001

Бренд: Case Страницы: 306

Бренд: Takeuchi Страницы: 170

Multi-Lock Quick Coupler

Бренд: Dromone Страницы: 18

PC600-8 BACKHOE

Бренд: Komatsu Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды