Komatsu A87001 Скачать руководство пользователя страница 36

Страница: 36 / 51

FOREWORD

STANDARD TIGHTENING TORQUE

00-24

PC200/220LL-8

Tightening Torques For O-ring Boss Piping Joints

★

Unless there are special instructions, tighten the O-ring boss piping joints to the torque below.

Table Of Tightening Torques For O-ring Boss Plugs

★

Unless there are special instructions, tighten the O-ring boss plugs to the torque below.

Torque Table For Hoses (Taper Seal Type And Face Seal Type)

★

Tighten the hoses (taper seal type and face seal type) to the following torque, unless otherwise specified.

★

Apply the following torque when the threads are coated (wet) with engine oil.

Norminal No.

Thread diameter

Width across flat

Tightening torque N

•

m (lbf ft)

Range

Target

Varies depending on

type of connector.

35 - 63 (25.81 - 46.46)

44 (32.45)

03, 04

84 - 132 (61.95 - 97.35)

103 (75.96)

05, 06

128 - 186 (94.40 - 137.18)

157 (115.79)

10, 12

363 - 480 (267.73 - 354.02)

422 (311.25)

746 - 1010 (550.22 - 744.93)

883 (651.26)

Norminal No.

Thread diameter

Width across flat

Tightening torque N

•

m (lbf lb)

Range

Target

5.88 - 8.82 (4.33 - 6.50)

7.35 (5.42)

9.8 - 12.74 (7.22 - 9.39)

11.27 (8.31)

14.7 - 19.6 (10.84 - 14.45)

17.64 (13.01)

19.6 - 24.5 (14.45 - 18.07)

22.54 (16.62)

24.5 - 34.3 (18.07 - 25.29)

29.4 (21.68)

34.3 - 44.1 (25.29 - 32.52)

39.2 (28.91)

44.1 - 53.9 (32.52 - 39.75)

49.0 (36.14)

58.8 - 78.4 (43.36 - 57.82)

68.6 (50.59)

93.1 - 122.5 (68.66 - 90.35)

107.8 (79.50)

107.8 - 147.0 (79.50 - 108.42)

124.4 (91.75)

127.4 - 176.4 (93.96 - 130.10)

151.9 (112.03)

181.3 - 240.1 (133.72 - 177.08)

210.7 (155.40)

274.4 - 367.5 (202.38 - 271.05)

323.4 (238.52)

Nominal

size of hose

Width

across flats

Tightening torque (N•m (lbf ft))

Taper seal

type

Face seal type

Range

Target

Thread size

(mm)

Nominal thread

size - Threads per

inch, Thread

series

Root diameter (mm)

(Reference)

34 - 54 (25.0 - 39.8)

44 (32.4)

9/16 - 18UN

14.3

34 - 63 (25.0 - 46.4)

44 (32.4)

54 - 93 (39.8 - 68.5)

74 (54.5)

11/16 -16UN

17.5

59 - 98 (43.5 - 72.2)

78 57.5)

84 - 132 (61.9 - 97.3)

103 (75.9)

13/16 - 16UN

20.6

128 - 186 (94.4 - 137.1) 157 (115.7)

1 - 14UNS

25.4

177 - 245 (130.5 - 180.7) 216 (159.3)

1 3/16 - 12UN

30.2

(10)

177 - 245 (130.5 - 180.7) 216 (159.3)

(12)

197 - 294 (145.3 - 216.8) 245 (180.7)

(14)

246 - 343 (181.4 - 252.9) 294 (216.8)

Содержание A87001




















































Результаты поиска

Содержание A87001

Отзывы:

Похожие инструкции для A87001

Бренды по названию

Популярные бренды

Komatsu A87001, Руководство по ремонту

Результаты поиска

Содержание A87001

Отзывы:

Похожие инструкции для A87001

Бренды по названию

Популярные бренды