Kolpin Powersports 180?? Скачать руководство пользователя страница 42

Страница: 42 / 87

FIG-18. Engine Disassembly

LUBRICATION

SERVICE INFORMATION

GENERAL

This section describes inspection and replacement of the

engine oil, oil filter screen and assembly of the oil

pump.

Fill the oil pump with clean oil when reassembling the

pump.

SPECIFICATIONS

Engine Oil Capacity

Engine Oil Recommendations

OIL PUMP

STANDARD

Cover-to-rotor clearance

Rotor tip clearance

End clearance

TORQUE VALUE

Oil Drain Bolt

TROUBLE SHOOTING

Oil level too low / high oil consumption

Normal oil consumption.

External oil leaks.

Oil not changed often enough.

Worn piston rings.

Faulty head gasket.

Oil contamination

Worn piston rings.

Faulty head gasket.

Oil or filter not changed often enough.

0.8-1.0 Liters

Viscosity: (

SAE 15W-40)

API Service classification: SF-SG

SERVIC LIMIT

--------- 0.12

0.01-0.10 0.2

20~30 n-m (2.0~3.0 kg-m)

Содержание 180??
























































































Результаты поиска

Содержание 180??

Отзывы:

Похожие инструкции для 180??

Бренды по названию

Популярные бренды

Kolpin Powersports 180??, Руководство по обслуживанию

Результаты поиска

Содержание 180??

Отзывы:

Похожие инструкции для 180??

Бренды по названию

Популярные бренды