Kolpin Powersports 180?? Скачать руководство пользователя страница 22

Страница: 22 / 87

FIG-04. Fender

FRONT FENDER COVER

Loosen the screws (a-1)

Remove the front fender cover (a-2)

(Photo 4)

BUMPER COVER

Loosen the screws (a-1)

Loosen the screws (a-2)

Take off the main wire connect with the lights wire (a-3)

Remove the front fender cover (a-4)

(Photo 5)

LICENSE PLATE

Loosen the screws (a-1)

Loosen the screws (a-2)

Take off the main wire connect with the lights wire (a-3)

Remove the license plate (a-4)

(Photo 6)

SEAT ASS'Y

Pull the “Seat Release Bar” to take off the seat. (a-1)

This seat release bar is under the right side of the rear

fender. Remove the seat ass’y

(Photo 7)

FRONT FENDER

Loosen the screws (a-1)

Loosen the hex bolt with plain washer (a-2)

Take off the fuel tank cap

Remove the front fender (a-4)

(Photo 8)

FRONT FENDER

Loosen the screws (a-1)

Loosen the hex bolt with plain washer (a-2)

Remove the front fender (a-3)

(Photo 8)

CAUTION

1. The battery and the toolbox are put under the seat.

Содержание 180??
























































































Результаты поиска

Содержание 180??

Отзывы:

Похожие инструкции для 180??

Бренды по названию

Популярные бренды

Kolpin Powersports 180??, Руководство по обслуживанию

Результаты поиска

Содержание 180??

Отзывы:

Похожие инструкции для 180??

Бренды по названию

Популярные бренды