background image

6 Transporting and storing the generating set

6.1

Transport and handling conditions

The unit should be handled gently and sudden movements should be avoided. Ensure that  the place where it is to be stored or 
used  is  carefully  prepared  beforehand.  Before  any  fixed  installation  on  a  trailer  or  inside  a  vehicle,  consult  one  of  our  approved 
agents.
Before transporting the unit, take the following necessary precautions:

1.

Check that the routes to be used are smooth and drivable. If it proves necessary to use uneven roads, drain the fuel into a 
container before setting off.

2.

Check that the bolts are correctly tightened, close the fuel tap (if fitted) and disconnect the battery (if fitted). 

3.

The unit should always be transported in its normal operating position; never lay it on its side. Ensure that the unit cannot 
fall from the vehicle carrying it, but without exerting too much force (risk of damaging the unit).

6.2

Storage conditions

This procedure for storing the unit or protecting it over the winter must be respected if it is not used for a period of up to 1 year. For 
longer  periods  of  storage,  it  is  recommended  to  contact  your  nearest  agent  or  to  start  up  the  unit  for  a  few  hours  every  year, 
ensuring that the storage procedure is respected afterwards.

Drain the fuel and change the engine oil:

1.

Start the unit and allow it to operate until it runs out of fuel.

2.

Set the switch to OFF (A7).

3.

Clean the sediment bowl.

4.

Close the fuel taps (A5).

5.

Top up the oil.

Grease

 

the cylinder and valves:

6.

Remove the spark plug (A16-F2) then, via its aperture, pour in approx. one teaspoon of new engine oil.

7.

Refit a new spark plug in its place.

8.

Pull the starter-recoil reel handle (A9) several times to distribute the oil inside the cylinder.

Storing the unit:

9.

Clean the unit.

10. Cover it with a protective cover and store it in its normal position, in a clean, dry and well ventilated area.

7 Repairing minor faults

The unit…

Check that:

Solutions to be applied:

Does not start

The checks before starting have been 

performed.

NO

Perform the necessary checks.

YES

The start-up procedure has been 

followed correctly.

NO

Re-read the start-up procedure and repeat 

the start-up attempt.

YES

The equipment to be used has not 

been connected prior to starting.

NO

Disconnect the equipment then try to start 

the unit again.

YES

The spark plug is in good condition and 

correctly connected.

NO

Replace the spark plug (330830012).

YES

Stops

The oil level is correct.

NO

Top up with oil

.

YES

The fuel level is correct.

NO

Fill up with fuel

.

YES

The air filter is in good condition.

NO

Clean the air filter.

YES

Does not function normally 

(noise, smoke, etc.)

Maintenance has been correctly 

performed on the unit components.

NO

Perform maintenance on the unit as per 

the recommendations.

YES

Have the unit checked by one of our 

agents*.

Does not supply electrical 

current

The circuit breaker(s) has/have been 

tripped.

NO

Check the capacity of the unit and press 

the circuit breakers.

YES

The connected equipment and their 

power cords are not faulty.

NO

Try with another item of equipment and 

another power cord.

YES

Have the unit checked by one of our 

agents*.

*France: 0.806.800.107 (call charge).

19/22

Содержание SDMO PERFORM 3000 XL TB UK C5















Отзывы: