background image

-1-

·

·

·

·

Please read these instructions carefully to
familiarize yourself with the required tools, materials,
and installation sequences. Follow the sections that
pertain to your particular installation. This will help
you avoid costly mistakes. In addition to proper
installation, read all operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-

Please provide adequate available space for the
bath unit in accordance with rough-in. Arrange the
location of drain in advance.

All installations must comply with council and local
authority by-laws. It is the responsibility of the installer
to ensure that the waste is made watertight by means
of silicone sealant or caulking compound.

Bath drain supplies and electric wiring should be
arranged preliminarily according to the selected bath.

please leave these

instructions for the consumer.

IMPORTANT:

NOTE:

Bath can be installed after the wall is completed.

·

·

·

·

BEFORE YOU BEGIN

368

201419

32" HOURGLASS 32"

SYMBIO

INSTALLATION INSTRUCTIONS

INTEGRATED WHIRLPOOL

K-1753T/K-1754T K-1773T/K-1774T

, 2007

Copyright Kohler China Ltd., 2007

PRODUCT NOTICES

A.

(GFCI)

(ELCB)

A. Installation Hazard Notification

DANGER: Risk of fire, electric shock, or injury to
persons.

WARNING: Risk of electrical shock.

WARNING: Risk of electrical shock.

WARNING: Risk of electrical shock.

WARNING: Risk of injury or property damage.

NOTICE:

Read important safety instructions on inside

front cover of these instructions.

A licensed

electrician should make all electrical connections.

Connect only to

a circuit protected by a Ground-Fault Circuit-Interrupter
(GFCI) or Earth-Leakage Circuit-Breaker (ELCB).

Disconnect

power before servicing.

Please read all instructions thoroughly before beginning
installation, including the following Product
Requirements.

Follow all local plumbing and electrical codes.

1073414-T01-B

Содержание K-1753T












Отзывы: