Kohler APM802 Скачать руководство пользователя страница 8

Страница: 8 / 48

TT-1625 7/17

User Programmed Inputs

#1 to #5

Monitors five

digital inputs (status, warnings, added user inputs

and/or shutdowns). Use the SiteTech

software to

select the desired user input and assign a severity level

(warning or shutdown fault). A separate yellow or red

LED flashes for each input when a respective warning or

shutdown fault occurs or the status changes. See

Figure 7.

Note:

If in SiteTech

the user attempts to assign a

digital input outside of the range for the controller

or ATS, an error message will be displayed by

SiteTech

and the Common Fault LED and

associated User Input LED will flash.

The five user input LEDs automatically correspond to

the on-board terminal blocks labeled USER 1 to 5, in

order of their numeric designators (LED1 to Input1 etc.),

unless altered using SiteTech

. Any digital input from

the Kohler generator controllers and ATS can be

associated with any of the five user input LEDs.

User-defined digital inputs #1 through #5 are selected at

the RSA III master only using SiteTech

software and

annunciated to the RSA III slave(s). No user-defined

digital input selection is available at the RSA III slave(s).

User-defined digital inputs tied directly to the RSA III

master are considered local. User-defined digital inputs

connected to the controller are considered remote.

Note:

Although all digital inputs are selectable on the

RSA III, some digital inputs have assigned

functions. Check the generator set configuration

to determine input availability.

DEC 3+ Controller.

User-defined digital input #3 is

also used for high battery voltage and requires

battery charger with alarms.

DEC 550, DEC 3000, DEC 3500, and DEC 6000

Controllers.

User-defined digital inputs tied directly

to the RSA III master are considered local.

DEC 8000 and APM802 Controllers.

User-defined

inputs tied to controller terminal block are considered

remote.

Figure 6 shows the status of the system ready LED,

generator running LED, communication status LED,

common fault LED, common fault output, and horn for

each fault or status condition.

Mounting

Surface Mounting or Flush Mounting

capability is

standard.

This document includes installation information for both

surface- and flush-mount models.

Safety Precautions

Observe the following safety precautions while

installing the kit.

Accidental starting.

Can cause severe injury or death.

Disconnect the battery cables before

working on the generator set.

Remove the negative (--) lead first

when disconnecting the battery.

Reconnect the negative (--) lead last

when reconnecting the battery.

WARNING

Disabling the generator set. Accidental starting can

cause severe injury or death.

Before working on the

generator set or equipment connected to the set, disable the

generator set as follows: (1) Shut down the generator set. (2)

Place the controller in Out of Service mode. (3) Press the

emergency stop button. (4) Disconnect the power to the

battery charger, if equipped. (5) Remove the battery cables,

negative (--) lead first. Reconnect the negative (--) lead last

when reconnecting the battery. Follow these precautions to

prevent the starting of the generator set by the remote

start/stop switch.
(APM802 Controller)

Disabling the generator set. Accidental starting can

cause severe injury or death.

Before working on the

generator set or equipment connected to the set, disable the

generator set as follows: (1) Move the generator set master

switch to the OFF position. (2) Disconnect the power to the

battery charger. (3) Remove the battery cables, negative (--)

lead first.

Reconnect the negative (--) lead last when

reconnecting the battery. Follow these precautions to prevent

starting of the generator set by an automatic transfer switch,

remote start/stop switch, or engine start command from a

remote computer.
(Decision-Maker

3+ and 550 Controllers)

Disabling the generator set. Accidental starting can

cause severe injury or death.

Before working on the

generator set or equipment connected to the set, disable the

generator set as follows: (1) Press the generator set off/reset

button to shut down the generator set. (2) Disconnect the

power to the battery charger, if equipped. (3) Remove the

battery cables, negative (--) lead first. Reconnect the negative

(--) lead last when reconnecting the battery. Follow these

precautions to prevent the starting of the generator set by the

remote start/stop switch.
(Decision-Maker

3000, 3500, and 6000 Controllers)

Содержание APM802

















































Результаты поиска

Содержание APM802

Отзывы:

Бренды по названию

Популярные бренды

Kohler APM802, Руководство по установке

Результаты поиска

Содержание APM802

Отзывы:

Бренды по названию

Популярные бренды