manualshive.com logo in svg

Kohler APM802, Руководство по установке

Поделиться
Скачать
Kohler APM802 Скачать руководство пользователя страница 16

16

TT-1625 7/17

GM85125-A

Note:

Dimensions shown are in mm.

25.4 mm is equal to 1 inch.

Figure 17

RSA III Mounting Hole Dimensions in Supplied Box GM85123

5.2

Remove four screws X-67-154 from the RSA III

bezel GM85134 and remove bezel from the

RSA III box GM85123. See Figure 17 for RSA III

supplied box mounting hole information.

The installation instructions describe three RSA III

mounting scenarios:

D

Surface mount with supplied box (step 5.3).

D

Flush mount with supplied box (step 5.4).

D

Flush mount using a user-supplied Hoffman box

(step 5.5).

5.3

Surface mount RSA III initial installation.

5.3.1 Prepare the mounting site by drilling pilot

holes for anchors, if used.

Note:

Mount the RSA III box to a standard 10 cm

(4 in.) square electrical box installed in the

wall.

5.3.2 Create an opening in the wall for the

electrical wiring from the master RSA III to

the controller communications and power

supply. The wall opening must allow for

the wiring of the RSA III slave, if used.

Protect the RSA III front panel assembly

from dust and debris when drilling the

holes.

5.3.3 Drill an appropriate size hole in box

GM85125 if a user-supplied conduit

connector is required. Install the user-

supplied connector.

5.3.4 Temporarily mount the RSA III box to the

wall or to the electrical box in the wall and

check for proper hole alignment. Adjust as

needed. Remove RSA III box.

Note:

Use mounting hardware suitable for the

wall composition and thickness.

5.3.5 Repeat step 3 for RSA III slaves, as

needed.

5.3.6 Proceed to step 6, Wire the RSA III.

5.4

Flush mount RSA III initial installation with

box GM85125 (Part of RSA III kit).

5.4.1 Prepare mounting site by creating an

opening in wall for flush-mounting RSA III

box.

Содержание APM802

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды