Kohler 14/20RESA Скачать руководство пользователя

Страница: 18 / 72

TP-6803 6/15

18 Section 1 Installation

1.8.2

Fuel Conversion, 14RESA/RESAL

Equipped with Fuel Orifice

Fittings

Note:

Model 14RESA/RESAL generator sets built

before June 26, 2014, use a fuel block for the fuel

type selection. See Figure 1-9 and use the

instructions Section 1.8.1 for fuel conversion.

Model 14RESA/RESALgenerators built June 26,

2014, or later are not equipped with the fuel block.

These units use fuel orifice fittings installed in the

hose fitting at the fuel regulator. See Figure 1-11

and use the instructions in this section for fuel

conversion.

For natural gas and LPG fuel, orifice fittings are used in

the fuel line. See Figure 1-10. The natural gas orifice

fitting is silver in color and stamped NG. The LPG fitting

is gold in color and stamped LPG. The fittings are

threaded. A straight-blade screwdriver is required to

remove and replace the fittings.

LPG

Figure 1-10

NG and LPG Fuel Orifice Fittings

The unit is typically shipped set up for natural gas, with

the LPG fitting tied near the fuel solenoid valve. To

convert to LPG, remove the NG fitting and install the

LPG fitting as described below. See Figure 1-11 for the

fuel system component locations.

Procedure to Convert from NG to LPG,

14RESA/RESAL with fuel orifice fittings

1. Press the OFF button on the generator set

controller.

2. Disconnect the utility power to the generator.

3. Disconnect the generator set engine starting

battery, negative (--) lead first.

4. Turn off and disconnect the fuel supply.

5. Remove the hose clamp and fuel hose from the

hose fitting. See Figure 1-11.

1. LPG fitting tied to bracket for shipping

2. Fuel hose and clamp

3. Ignition timing leads

Ignition Timing Lead Connection

Figure 1-11

Fuel System, As Shipped (Model

14RESA/RESAL built after June 26,

2014)

6. Use a straight-blade screwdriver to remove the NG

orifice from the hose fitting. See Figure 1-12.

7. Insert the LPG orifice into the hose fitting. Use a

straight-blade screwdriver to tighten the fitting until

it is snug.

8. Slide the hose onto the hose fitting and secure it

with the clamp.

9. Disconnect ignition timing leads 65 and N3 for

LPG. The ignition timing leads are located near the

fuel solenoid valve. See Figure 1-11.

Содержание 14/20RESA









































































Результаты поиска

Содержание 14/20RESA

Отзывы:

Похожие инструкции для 14/20RESA

Бренды по названию

Популярные бренды

Kohler 14/20RESA, Руководство по установке

Результаты поиска

Содержание 14/20RESA

Отзывы:

Похожие инструкции для 14/20RESA

Бренды по названию

Популярные бренды