manualshive.com logo in svg

Kohler 125EOZ/100EFOZ, Руководство по обслуживанию

Поделиться
Скачать
Kohler 125EOZ/100EFOZ Скачать руководство пользователя страница 91

TP-5737 5/01

77

Section 7 Component Testing and Adjustment

7.14 Governor Adjustment

7.14.1 Mechanical Governor

Note:

Before checking and adjusting engine
speed, make sure the engine reaches its
normal operating temperature.

Note:

All speed specs apply to an engine at
operating

temperature

under

load

conditions.

The

maximum

permissible

speed variation is 2--3 Hz or 50--90 rpm for
fast idle speed.

Mechanical Governor Adjustment Procedure

1. Disconnect the speed control from the fuel injection

pump lever and start the engine.

2. Verify that the injector pump lever holds in the fast

idle position against the fast idle adjusting screw.
See Figure 7-23.

3. Using a frequency meter, check the engine speed.

Adjust the engine speed at full load to 1800 rpm
(60 Hz) or 1500 rpm (50 Hz).

To increase the

engine speed, turn the fast idle adjusting screw
counterclockwise; turn the fast idle adjusting screw
clockwise to decrease engine speed.

4. Reconnect the speed control to the fuel injection

pump lever.

5. Stop the generator set.

TP-5353-7

1

2

1. Injection pump lever
2. Fast idle adjusting screw

Figure 7-23

Governor Adjustments, Typical

7.14.2 Electronic Governor—Barber-

Colman Dyna 2500 125--150 kW
John Deere Engine-Powered 6081

Some sets are equipped with Barber-Colman Dyna
2500 electronic governors.

Because this is an

electronic device, no mechanical drive or hydraulic
connection is required.

The system consists of a

magnetic pickup, an electronic control unit, and an
actuator. The magnetic pickup monitors engine speed
and transmits this information to the electronic control
unit (see Figure 7-24 or Figure 7-25). The electronic
control unit interprets the signal from the magnetic
pickup to control current input to the throttle actuator.
The throttle actuator adjusts the throttle position on the
engine. See Figure 7-26.

KC250000B-A

1

2

3

4

5

6

7

1. Control unit
2. Magnetic pickup
3. Actuator
4. Connect to safeguard breaker terminal strip
5. Connect to cranking solenoid, battery (+)
6. Connect to 70 on safeguard breaker terminal block
7. Relay

Figure 7-24

Governor Control Unit,
Nonparalleling Generator Set

Содержание 125EOZ/100EFOZ





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды