Kohler 125EOZ/100EFOZ Скачать руководство пользователя страница 45

Страница: 45 / 148

TP-5737 5/01

Section 5 Decision-Maker

3+ Troubleshooting

5.1.2

Fault Shutdowns,
Decision-Maker 3+ Controller

If the generator set does not start or stops running
because of a fault shutdown (fault lamp lit), refer to

Figure 5-13 to identify fault conditions. Consult the
Engine Service Manual for detailed information on
correcting engine-related faults. To reset the set after a
fault shutdown, see Section 2, Operation.

Indicator

Fault Condition/Causes

High engine temperature lamp

Engine coolant temperature is above shutdown range; see Section 1, Specifications

High engine temperature lamp
lights

Cooling system malfunction

Low oil pressure lamp lights

Engine oil pressure is below shutdown range, see Section 1, Specifications

Overspeed lamp lights

Governed frequency is in excess of 70 Hz (2100 rpm)

Continuous cranking is more than 45 seconds

Overcrank lamp lights

Cyclic cranking is more than 75 seconds

p g

Locked rotor

Overcrank lamp flashes

Speed sensor signal is absent longer than one second

No AC output is present

Auxiliary lamp flashes

Battery power was reconnected or was low and then came back up again while generator
set master switch was in the RUN or AUTO position

Optional emergency stop switch is reset while the generator set master switch is in the RUN
or AUTO position

Auxiliary lamp lights

High exhaust temperature (P1-14) or auxiliary delay shutdown (P1-15) faults occur, if sensor
equipped

Auxiliary lamp lights

Overvoltage, if equipped, has occurred, voltage 15% greater than nominal voltage (for
period longer than two seconds)

Activated by customer-supplied sensing device connected to auxiliary immediate shutdown
ports (P1-17 and P1-18)

Emergency stop if equipped

Emergency stop switch is activated (local or remote)

Emergency stop, if equipped

Emergency stop switch(es) are disconnected from controller terminals TB1-1 or 1A

Multiple lamps light (where
illumination may appear dim)

Main circuit board F1 (3-amp) fuse blown. F1 fuse supplies battery voltage to a remote
annunciator and/or dry contact kit.

Figure 5-13

Fault Shutdown Troubleshooting Chart

Содержание 125EOZ/100EFOZ





















































































































































Результаты поиска

Содержание 125EOZ/100EFOZ

Отзывы:

Бренды по названию

Популярные бренды

Kohler 125EOZ/100EFOZ, Руководство по обслуживанию

Результаты поиска

Содержание 125EOZ/100EFOZ

Отзывы:

Бренды по названию

Популярные бренды