Kohler 1237791-2-G Скачать руководство пользователя страница 11

Страница: 11 / 38

Operating Instructions

IMPORTANT!

This product contains an automatic water purge mode that turns the blower on for 2

minutes approximately 30 minutes after the unit is turned off and drained.

NOTE:

The water temperature in the bath should never exceed 104°F (40°C).

Close the drain, then fill the bath at least 4” (102 mm) above the top of the highest airjet.

Use your hand to test the water temperature for comfort and safety, then carefully enter the bath.

Press the [On/Off] icon to turn the blower on at medium speed.

Press the [Up] or [Down] arrow icons to increase or decrease the air flow.

NOTE:

The blower will turn off automatically following 20 minutes of operation, and can be immediately

restarted if desired.

Press the [On/Off] icon a second time to turn off the blower.

Carefully exit and drain the bath.

Press the [Purge Mode] icon to blow remaining water from the air channels. The blower will turn
on for 2 minutes and then turn off automatically.

NOTE:

About 30 minutes after the blower motor stops, a 2 minute purge mode will automatically start.

NOTE:

If the bath does not function properly, refer to the

″

Troubleshooting

″

section.

Care and Cleaning

Do not use powdered cleaners unless the cleaner is fully dissolved in water.

Solid substances

could block the airjets.

Do not use full strength bleach or ammonia cleaning solutions.

Chemically active cleaning

solutions can damage the bath surface.

Do not use abrasive cleansers or solvents on acrylic surfaces.

Abrasive cleaners and solvents can

damage the bath surface.

Wipe out your acrylic bath with a soft cloth after each use.

Avoid detergents, disinfectants, or cleaning products in aerosol cans.

NOTE:

To restore dull or scratched units: Apply white automotive polishing compound with a clean rag.

Rub scratches and dull areas vigorously. Wipe off residue. Follow with a coat of white automotive paste
wax. Do not wax areas where you walk or stand.

Purge Mode

On/Off

Increases Flow

Decreases Flow

Kohler Co.

1237791-2-G

Содержание 1237791-2-G







































Результаты поиска

Содержание 1237791-2-G

Отзывы:

Похожие инструкции для 1237791-2-G

Бренды по названию

Популярные бренды

Kohler 1237791-2-G, Руководство по установке и эксплуатации

Результаты поиска

Содержание 1237791-2-G

Отзывы:

Похожие инструкции для 1237791-2-G

Бренды по названию

Популярные бренды