background image

  

  

  

  

  

  

 

2

  

SAFETY FIRST 

This symbol, the industry’s “Safety Alert Symbol”, is used throughout this manual to warn of the 

possibility  of  personal  injury  or  equipment  damage.    Read  these  instructions  carefully.  It  is 

essential that you read the operating instructions and safety instructions  before you attempt to 

assemble or use this unit. 

NEVER ADD GASOLINE 

to a hot engine as this can result in a fire or explosion. 

  Always shut off engine before refueling. 

  When  refueling,  keep  all  flames,  sparks  and  cigarettes  away  from  the  power 

washer 

  Do  not  over-fill  the  fuel  system.    If  any  fuel  spills,  wipe  it  up  completely  before 

starting engine. 

  Refer to the  Honda engine manual on engine cooling 

   

BEFORE  TRANSPORT

,  ensure  that  the  fuel  is  shut  off  and  that  the  unit  is  in  the 

upright  position  to  avoid  fuel  spillage.    Fuel  vapor  or  spilled  fuel  may  ignite. 

INVESTIGATE AND ABIDE BY YOUR LOCAL LAWS IN THE TRANSPORTATION 

OF ENGINES WITH GASOLINE IN THEM. 

NEVER  AIM  SPRAY  AT  YOURSELF  OTHER  PEOPLE  OR  ANIMALS.

    The  high 

pressure water stream can cause injury or death. 

NEVER DIRECT SPRAY

 at pressure washer unit. 

 

Failure to install the yellow vented plug in the pump crankcase may cause personal 

injury,  will damage the pump and void warranty. 

 

Failure to properly connect the high pressure hose can result in injury. 

 

Unloader  valve  is  preset  for  safe  operation.    It  has  been  set  to  not  exceed  the 

maximum allowable water pressure for your unit.  DO NOT attempt to tamper with the 

preset factory setting. 

 

To avoid injury and unintentional spraying, always engage the red trigger lock on the 

trigger of the gun when not spraying. 

AFTER MACHINES ENGINE IS STOPPED

, failure to relieve the high pressure from 

the  system  before  disconnecting  any  hoses  may  result  in  injury.  Bleed  off  high 

pressure by turning off the water to the unit and pulling on the trigger. 

Содержание KC4035GPB













Отзывы: