Kodak ENCAD NOVAJET 750 страница 26 Скачать руководство пользователя | Manualshive

Страница: 26 / 32

background image

NJ750 Training Guide

26

NOTE:

Before you can configure a Windows print queue, you must first configure an IP

address on both your PC and the SEH print server.

1. PC PROTOCOL SETUP

1. If you have not already done so, install the TCP/IP protocol on your PC. This is done

by first RIGHT-CLICKING on the My Network Places icon on your desktop. Select
Properties from the list. The Network dialog box appears.

2. Double click on the Local Area Connection icon. When the Local Area Connection

dialog box opens, double click on the TCP/IP protocol to activate the TCP/IP
properties. See figure below.

3. Once the TCP/IP properties dialog box is open enter the information as follows:
IP Address-

192.168.254.201

SUBNET Mask-

255.255.255.0

DNS Server-

192.168.254.195

«
...
24
25
26
27
28
...
»

Содержание ENCAD NOVAJET 750

































Отзывы:

Нет отзывов

Похожие инструкции для ENCAD NOVAJET 750

Бренд: QMS Страницы: 311

WorkCentre Pro 421

Бренд: Xerox Страницы: 4

WorkCentre Pro 412

Бренд: Xerox Страницы: 212

WORKCENTRE PE 220

Бренд: Xerox Страницы: 8

WORKCENTRE PE 220

Бренд: Xerox Страницы: 2

WORKCENTRE PE 220

Бренд: Xerox Страницы: 200

WorkCentre m940

Бренд: Xerox Страницы: 86

Бренд: Xerox Страницы: 24

WorkCentre PE16

Бренд: Xerox Страницы: 201

WorkCentre M24 Color

Бренд: Xerox Страницы: 441

WORKCENTRE C2424

Бренд: Xerox Страницы: 2

WorkCentre M118

Бренд: Xerox Страницы: 5

WORKCENTRE C2424

Бренд: Xerox Страницы: 16

WORKCENTRE C2424

Бренд: Xerox Страницы: 20

WORKCENTRE C2424

Бренд: Xerox Страницы: 25

2006NPC - DocuColor Color Laser

Бренд: Xerox Страницы: 4

WorkCentre XK50cx

Бренд: Xerox Страницы: 90

Бренд: Xerox Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды