Kodak ENCAD NOVAJET 750 страница 25 Скачать руководство пользователя | Manualshive

Страница: 25 / 32

background image

NJ750 Training Guide

25

Configuration for

Windows 2000/XP

Printer Networking is a basically a 3-step Process:

1. Assign TCP/IP address of host computer/server
2. Assign TCP/IP address to print server (may also need to install windows

printer port during this process)

3. Assign TCP/IP address to RIP (same as print server)

For the most recent software version (i.e. InterCon NetTool) go
to the following URL:

http://www.seh.de/

NOTE:

The most common download, for PC users, from SUPPORT -

FIRMWARE/SOFTWARE (select IC105 FastPocket-TX) is:

Version 1.8.23 for Win 2000, Win XP, Win 9x

Administration tool for InterCon print servers.

«
...
23
24
25
26
27
...
»

Содержание ENCAD NOVAJET 750

































Отзывы:

Нет отзывов

Похожие инструкции для ENCAD NOVAJET 750

Бренд: Oki Страницы: 6

Бренд: Oki Страницы: 44

Бренд: Oki Страницы: 13

Бренд: Oki Страницы: 20

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 28

Бренд: 3D Systems Страницы: 26

Бренд: 3D Systems Страницы: 39

WorkSeries 200 Series

Бренд: 3D Platform Страницы: 9

Figure 4 Standalone

Бренд: 3D Systems Страницы: 2

Бренд: Olivetti Страницы: 139

Бренд: Oki Страницы: 180

Бренд: U-Line Страницы: 18

Бренд: Konica Minolta Страницы: 8

INFOPRINT HI-LITE COLOR 4005-HC2

Бренд: IBM Страницы: 10

Бренд: Gerber Страницы: 163

Бренд: Konica Minolta Страницы: 4

Бренд: Monarch Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды