9
F
*AUTOTIMER (600...660)
A Timer function can also be set via the
IR remote control. This is particularly
relevant for the EKTAPRO 7010/7020 as
this does not have a built-in timer.
Any time from
1 to 60 seconds
can be set
(in steps of one second). If you transmit
such a command to the MASTER projec-
tor, the first transport command or the
first dissolve is carried out immediately.
This is a check for you that the projector
is now in autotimer mode.
Example
You want a dissolve to take place every 22
seconds:
è
Press <622> and <*> on your remote
control.
The slide tray goes to position 1 and the first
picture with the dissolve time is faded up. The
first dissolve occurs after 22 seconds.
Important
:
Whilst the MASTER projector is carry-
ing out a slide transport, no commands
should be sent with the IR remote con-
trol. This can lead to the command not
being recognised, especially in the case
of very short autotimer times. In this case
the projector should be switched off- and
on again.
Switching the autotimer off
You can turn the autotimer off again at
any time:
Press <600> and <*> on your remote
control.
Transport control on the MASTER:
The slide transport runs, as usual, via the
two transport buttons.
Transport control on the SLAVE:
The slide transport is via the two
focus
buttons
.
It is therefore not possible to focus the
two projectors with this setting!
Access to individual slides (RA control)
is still possible (see Random Access).
F
PARALLEL PROJECTION (970)
You can also program parallel projec-
tions via your remote control.
Press <970> and <*>.
Both projectors will then move to the
same slide tray setting and both lamps are
switched on.
Focussing:
MASTER: With the focus buttons.
SLAVE: First press <666> and <*>, then
use focus buttons (not possible with
models 7010 and 9010!).
With a next slide transport this command
is inactive again.
The slides are numbered from 1 - 80 (or 1
- 140 on a 140 slide tray) in this parallel
mode and can be selected as such. If, for
example, no. 13 is selected, both projec-
tors will go into search mode and project
the slides in the slide tray slot no. 13.
F
BACK INTO DISSOLVE MODE
(990)
By inputting this combination of num-
bers and the <*> you can go back to a
basic setting for the two projector dis-
solve. The dissolve time previously set is
retained.
Press <990> and <*> on your remote
control.
F
*SECURITY SETTING FOR PRES-
ENTATIONS USING IR REMOTE CON-
TROL (989)
If all the preparations for a presentation
have been made, it is impor-
tant for a presentation to run
smoothly. In spite of the
best preparation small
hitches can occur if the
presenter presses the
wrong button on the
remote control by accident.
With the security setting you can set up
your remote control so that when the trans-
port button is pressed, only one transport
step or only one dissolve is executed. The
focus buttons are also disabled so that if
you happen to press the buttons, the focus
on the projector is not changed. All other
functions remain active (and can be se-
cured by the cover on the remote control).
Even novice presenters can now not put
a foot wrong!
This is how to put your remote control into
the security position:
Press (989) and <*>.
The following functions are changed:
n
Transport forwards:
Regardless of how long you press a but-
ton, the projector only carries out a single
transport step or the next dissolve. In case
the parallel mode is activated the slides will
only be projected if the button is released.
n
Transport backwards:
Hold down the button for at least two
seconds. The projector carries out a single
step backwards and the slide will be pro-
jected in the moment the button is released.
n
Focus:
Inactive
Note
Of course the security position can also
be used to control projection with a single
projector.
For the individual projector control
(980) this command cannot be applied.
To cancel the security setting:
The presentation mode can only be can-
celled by a reset command or by switching
the projectors off and on again (see RE-
SET).
Press (999) and <*>.
F
*RESET (999)
When you input this command, the two
projectors are automatically reset to their
zero position. Reset is the same as switch-
ing the projectors off and back on again
(see also basic setting).
Press <999> and <*> on your remote
control.
