kobi NET-KOBI-IP-16CH Скачать руководство пользователя страница 160

Страница: 160 / 181

160

12.4

Upgrading System

Purpose:

The firmware on your NVR can be upgraded by local backup device or remote FTP server.

12.4.1

Upgrading by Local Backup Device

Steps:

Connect your NVR with a local backup device where the update firmware file is located.

Enter the Upgrade interface.

Menu >Maintenance>Upgrade

Click the

Local Upgrade

tab to enter the local upgrade menu, as shown in Figure 12. 12.

Figure 12. 12

Local Upgrade Interface

Select the update file from the backup device.

Click the

Upgrade

button to start upgrading.

After the upgrading is complete, reboot the NVR to activate the new firmware.

12.4.2

Upgrading by FTP

Before you start:

Configure PC (running FTP server) and NVR to the same Local Area Network. Run the 3

-party TFTP software

on the PC and copy the firmware into the root directory of TFTP.

Steps:

Enter the Upgrade interface.

Menu >Maintenance>Upgrade

Click the

FTP

tab to enter the local upgrade interface, as shown in Figure 12. 13.

Содержание NET-KOBI-IP-16CH






















































































































































































Результаты поиска

Содержание NET-KOBI-IP-16CH

Отзывы:

Бренды по названию

Популярные бренды

kobi NET-KOBI-IP-16CH, Руководство пользователя

Результаты поиска

Содержание NET-KOBI-IP-16CH

Отзывы:

Бренды по названию

Популярные бренды