background image

24

WARRANTY

  1.  DURATION: From the date of purchase by the original purchaser as follows: Three Years.
  2.  WHO GIVES THIS WARRANTY: Campbell Hausfeld  a Marmon/Berkshire Hathaway Company, 

100 Production Drive, Harrison, Ohio, 45030.

  3.  WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for 

purposes of resale) of the compressor.

  4.  WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: This air compressor.
  5.  WHAT IS COVERED UNDER THIS WARRANTY: Parts and Labor to remedy substantial 

defects due to material and workmanship during the first year of ownership with the exceptions 
noted below. Parts only to remedy substantial defects due to material and workmanship during 
remaining term of coverage with exceptions noted below.

  6.  WHAT IS NOT COVERED UNDER THIS WARRANTY: 

A.  Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR 

PURPOSE ARE LIMITED FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN 
THE DURATION. Some States do not allow limitations on how long an implied warranty 
lasts, so the above limitations may not apply to you

B.  ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE 

THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE 
CAMPBELL HAUSFELD PRODUCT. Some States do not allow the exclusion or limitations of 
incidental or consequential damages, so the above limitation or exclusion may not apply to 
you.

C.  Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate 

products in accordance with instructions provided in the owner’s manual(s) supplied with 
compressor.

D.  Pre-delivery service, e.g. assembly, oil or lubricants, and adjustment.
E.  Items or service that is normally required to maintain the product, i.e. lubricants, filters and 

gaskets, etc.

F.  Additional items not covered under this warranty:

1.  Excluded items pertaining to All Compressors

a.  Any component damaged in shipment or any failure caused by installing or operating 

unit under conditions not in accordance with installation and operation guidelines or 
damaged by contact with tools or surroundings.

b.  Pump or valve failure caused by rain, excessive humidity, corrosive environments or 

other contaminants.

c.  Cosmetic defects that do not interfere with compressor functionality.
d.  Rusted tanks, including but not limited to rust due to improper drainage or corrosive 

environments.

e.  The following components are considered normal wear items and are not covered 

after the first year of ownership. Electric motor, check valve, pressure switch, regulator, 
pressure gauges, hose, tubing, pipe, fittings and couplers, screws, nuts, hardware 
items, belts, pulleys, flywheel, air filter and housing, gaskets, seals, oil leaks, air leaks, 
oil consumption or usage, piston rings.

f.  Tank drain valves.
g.  Damage due to incorrect voltage or improper wiring.
h.  Other items not listed but considered general wear parts.
i.  Pressure switches, air governors, load/unload devices, throttle control devices and 

safety valves modified from factory settings.

j.  Damage from inadequate filter maintenance.
k.  Induction motors operated with electricity produced by a generator.

kobalttools.com

Содержание VT636201































Отзывы: