KNOVA KN RXW-10M3 Скачать руководство пользователя

Страница: 12 / 40

ASSEMBLE AND ADJUSTMENTS

Fig. 23

SWITCH

INSTALLATION:

Install the switch on

the location as Fig.23

with the hex. Screw

1/4” x 20UNC x 3/4”.

Lock the screw under

the Front rail, and

make sure you have

lock including star

washer A as Fig.23.

The table saw is equipped with a push-button switch that will

accept a padlock (not included) for locking the switch in the

OFF position. See Fig. 24. To safeguard your machine from

unauthorized operation and accidental starting by young

children, the use of padlock is necessary. Place the key in a

location that is inaccessible to children and others not

qualified to use the tool.

ADJUSTING THE MITER GAUGE

See Figure 25.

You can set the miter gauge

at 0º and plus or minus 45º

with the miter gauge stop

pin and adjustable stop screws.

Note:

The miter gauge provides close accuracy

in angled cuts. For very close tolerances,

test cuts are recommended.
• Loosen knob and pull out on stop pin

to rotate miter gauge base past stop screws.
• Loosen the lock nut of the 0º stop screw at

the stop pin with a 8mm wrench.
• Place a 90º square against the miter gauge

rod and the miter gauge base.
• If the rod is not square, loosen the knob,

adjust the rod, and tighten the knob.
• Adjust the 0º stop screw until

it rests against the stop pin.
• Adjust the plus and minus 45º stop screws

using a 45º triangle and the steps above.

Fig. 25

Miter gauge rod

Miter gauge

base

Knob

0º adjustable

stop screw

45º adjustable

stop screw

Lock nut

Fig. 22

Fig. 24

Содержание KN RXW-10M3









































Результаты поиска

Содержание KN RXW-10M3

Отзывы:

Похожие инструкции для KN RXW-10M3

Бренды по названию

Популярные бренды

KNOVA KN RXW-10M3, Руководство пользователя

Результаты поиска

Содержание KN RXW-10M3

Отзывы:

Похожие инструкции для KN RXW-10M3

Бренды по названию

Популярные бренды