Knoll MVP44A Скачать руководство пользователя страница 1

In Canada:

11791 Machrina Way #120

Richmond, B.C. V7A 4V3

Knöll Systems

tel (604)  272-4555

fax (604) 272-5595

Knöll Systems, Richmond, BC & Point Roberts WA

C

COPYRIGHT 1998-2003, Knöll Systems, All Rights Reserved

In America:

145 Tyee Drive, #1206

Point Roberts, WA 98281

Four stereo power amplifiers with

individual volume control electronics

and four input source selection

Limited Warranty

Knöll Systems warrants the its electronic products except projectors sold in Canada and the
USA by authorized Knöll dealers to be free from defects in materials and workmanship. This
warranty extends for three full years from the date of purchase by the consumer. Any
products returned freight prepaid to Knöll Systems and found to be defective by Knöll
Systems within the warranty period will be repaired or replaced at Knöll Systems option, at
no charge. Knöll Systems will not be responsible for the actual cost of installation or removal
of the product, nor for any consequential or incidental damages. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights. You may have
additional rights which vary from state to state. Knöll products sold outside of Canada and
the USA may be covered by warranties provided by an authorized Knöll distributor. Please
contact the distributor in the country that the Knöll product was purchased.

Printed in Canada

 

 

Version 3.3

INSTALLATION

MANUAL

MVP44a

systems

Specifications
MVP44a 8 Channel Power Amplifier

Inputs:

           4 pairs of gold RCA jacks

Input impedance:

24 k ohms

Outputs:

Gold 5 way Binding posts

Output power:

50 watts RMS per channel (8 ohms)

Peak output power: 100 watts RMS per channel (8 ohms)
Ideal impedance:

6-8 ohms

Freq. response:

10 Hz - 40 kHz +/- 1 dB (1w)

S/N ratio:

over 105 dB A weighted 50 watts

THD distortion:

<0.1% 20 Hz to 20 kHz

IMD distortion

<0.01% 60 Hz 7 kHz 4:1 (SMPTE)

Trigger control:

12VDC output 60mA max.

Power:

750 watts 117 VAC

Dimensions:

17" x 3.5" x 10.5"

Weight:

22 lbs (10 kg)

Operating Temp:

-20C to +60C (-4F to +140F)

Caution:

 

Never listen to sound that is distorted. If distorted sound

is heard, turn the volume down immediately or speaker
and/or amplifier damage could occur that is not covered by the
warranty. If this problem persists, contact your dealer.

Complies with part 15 of the FCC rules. Operation is subject to:
1. This device may not cause harmful interference
2. This device must accept any interference received
   including interference that may cause undesired operation.

It is very important to use a top quality

RJ45 8/8 crimper tool. We strongly

suggest using a cat 5 / RJ45 electronic

tester to verify the wire conductors.

Содержание MVP44A









Отзывы: