INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
BF1430EMS / BF2440EMS
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse, or circuit breaker
•
Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
•
Do not overload this accessory or subject it to conditions outside its rating
•
This product is Class II double insulated
•
This product is IP44 rated
INSTALLATION
Note -
Microwave sensors may not be suitable for all installations, for example enclosed spaces, as they are
able to detect movement through non-metallic surfaces like plasterboard and thin doors
•
Provide power to the required point of installation (refer to BS7671 for correct cabling methods).
Suitable IP rated junction boxes should be used where required
•
Remove the diffuser by turning the three diffuser clips 90° (see Fig. 1)
Fig. 1
•
Remove the three fixing screws securing the LED plate
•
Remove the LED plate and disconnect from the driver (via the DC socket) and emergency inverter (via
the YJD socket)
•
Drill the fixing holes in the rear of the fitting. Mark the location of the fixing holes and drill ensuring not
to infringe with any gas/water pipes or electrical cables
•
Feed the mains cable through the rubber grommet to retain IP rating, and secure the base plate to the
surface
•
Ensuring correct polarity is observed, carefully wire as shown in Fig. 2
Fig. 2
Fig. 1
• Remove the three fixing screws securing the LED plate
• Remove the LED plate and disconnect from the driver (via the DC socket) and emergency inverter (via the
YJD socket)
• Drill the fixing holes in the rear of the fitting. Mark the location of the fixing holes and drill ensuring not to
infringe with any gas/water pipes or electrical cables
• Feed the mains cable through the rubber grommet to retain IP rating, and secure the baseplate to the
surface
• Ensuring correct polarity is observed, carefully wire as shown in Fig. 2
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
BF1430EMS / BF2440EMS
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse, or circuit breaker
•
Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
•
Do not overload this accessory or subject it to conditions outside its rating
•
This product is Class II double insulated
•
This product is IP44 rated
INSTALLATION
Note -
Microwave sensors may not be suitable for all installations, for example enclosed spaces, as they are
able to detect movement through non-metallic surfaces like plasterboard and thin doors
•
Provide power to the required point of installation (refer to BS7671 for correct cabling methods).
Suitable IP rated junction boxes should be used where required
•
Remove the diffuser by turning the three diffuser clips 90° (see Fig. 1)
Fig. 1
•
Remove the three fixing screws securing the LED plate
•
Remove the LED plate and disconnect from the driver (via the DC socket) and emergency inverter (via
the YJD socket)
•
Drill the fixing holes in the rear of the fitting. Mark the location of the fixing holes and drill ensuring not
to infringe with any gas/water pipes or electrical cables
•
Feed the mains cable through the rubber grommet to retain IP rating, and secure the base plate to the
surface
•
Ensuring correct polarity is observed, carefully wire as shown in Fig. 2
Fig. 2
Fig. 2
