background image

               

User’s Information Manual

11

4  

SMART SYSTEM control module

Access modes

User

The user can adjust space heating and tank target temperatures 
by pressing the NAVIGATION dial when “

SETPOINTS” is 

flashing at the bottom of the display. The user can adjust 
the date and time, night setback override,temperature units, 
and night setback override (if active) by pressing the LEFT 
SELECT [MENU] key for 5 seconds. When the user password 

“0000” appears, then press the RIGHT SELECT [SAVE] key 
(do not change the password).

Installer

Most parameters are available only to the installer, accessible 
only by entering the installer password, see the Knight Boiler 
Service Manual.

Saving parameters 

Press the RIGHT SELECT [SAVE] key one time to return to 
the parameter listing.  Press the RIGHT SELECT [HOME] 
key again to store the new settings and return to the Status 
Screen.

Please note that the brackets ([]) denote 
screen status.

 NOTICE

Figure 4-1 Control Panel

Knight wall mount control module

Use the control panel (FIG. 4-1) to set temperatures, operating conditions, and monitor boiler operation.

NAVIGATION DIAL

The information on the bottom of the display shows the functions of the two SELECT keys (on either corner), and the 
NAVIGATION dial (in the center):  MENU = Left SELECT Key
 

 

 

 

  SETPOINTS = NAVIGATION Dial - Pressing Down

 

 

 

 

  SHDN = Right SELECT Key  

Adjusting parameters

Time and date

The control uses an internal clock for the night setback feature 
and for logging of events.  For these features to work properly, 
the clock must be set when the boiler is first installed or any 
time the boiler has been powered off for more than four (4) 
hours.  This parameter must be accessed to set the clock.  

 

CAUTION

Before changing parameters, note the 
settings so that the unit can be returned to 
its original operating parameters.

 NOTICE

The internal clock does not adjust for 
Daylight Savings Time and therefore, will 
require a manual adjustment.

To set the clock, access the clock menu as described in the 

User

 section.  Rotate the NAVIGATION dial (if needed) until 

the arrow (>) is pointing to “TIME & DATE”.  Press the 
NAVIGATION dial once.  If the date and time are incorrect, 
press the NAVIGATION dial again.  The hours value will 
begin flashing.  Rotate the NAVIGATION dial until the hour 
and AM/PM values are correct.  Press the NAVIGATION 
dial again.  The minutes value will begin flashing.  Rotate 
the NAVIGATION dial to adjust the minutes.  Repeat this 
procedure to adjust the month, date and year.  Save the new 
settings as described in the 

Saving Parameters

 section (this 

page).

Содержание WH 399

















Отзывы: