Knight 151 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 48

background image

3

Troubleshooting

(continued)

39

Table 3-4 (continued from previous page) Troubleshooting Chart - Fault Messages Displayed on Boiler Interface

FAULT

DESCRIPTION

CORRECTIVE ACTION

Flame Fail Ign

(cont’d)

(will require a manual

reset once the condition

has been corrected.

Press the RESET button

on the SMART SYSTEM

display to reset.)

The unit has failed to prove main burner
ignition after four (4) attempts.

• Verify that the plastic hose from the gas valve to the air
inlet is connected and is not damaged.

• Verify that the vent/air intake pipes are correctly
installed and that there are no obstructions.

• Check for 24 vac to the gas valve at the 2-pin
  connection on the side of the main control board during
  the ignition attempt. If no voltage is present, replace
  the main control board.

• If 24 vac is present at the main control board, check
the wiring between the main control board and the gas
valve. Replace the wiring if necessary.

• If 24 vac is present, check the outlet of the valve to
  ensure the valve is flowing gas. With a manometer
  connected to the outlet tap of the gas valve, when the
  unit is in the prepurge period, there should be a
negative pressure present. When the valve is
  energized a change in pressure should occur. If the
  pressure change does not occur, the gas valve is not
  opening. Replace the gas valve.

•

Inspect flame sensor and associated wiring.

Reference page 31 of this manual for removal and
cleaning procedures. Replace if necessary.

• Inspect and clean the heat exchanger as necessary.
Reference page 32 of this manual for cleaning
procedures.

• Inspect the burner. Reference page 31 of this manual
for removal and cleaning procedures. Replace if
necessary.

• Replace the main control board.

Flame Sequence

(will require a manual

reset once the condition

has been corrected.

Press the RESET button

on the SMART SYSTEM

display to reset.)

The flame detector circuit is seeing a flame
signal while no flame is present.

• Check supply voltage for proper polarity.

• Check external wiring for voltage feedback.

• Check the flame rod and make sure it is clean.

• Check the internal wiring for bad connections.

• Replace main control board.

Outdoor Knight Boiler Service Manual

«
...
37
38
39
40
41
...
»

Содержание 151

















































Отзывы:

Нет отзывов

Похожие инструкции для 151

Бренд: Protherm Страницы: 32

Бренд: ideal commercial Страницы: 36

INDEPENDENT C35

Бренд: IDEAL Страницы: 72

Бренд: Rima Heating Systems Страницы: 27

Бренд: VOKERA Страницы: 48

Бренд: DeDietrich Страницы: 20

Бренд: Viadrus Страницы: 76

Бренд: Beretta Страницы: 144

Бренд: Daikin Страницы: 416

Бренд: U.S. Boiler Company Страницы: 96

DynaFlame Series

Бренд: Camus Hydronics Страницы: 92

Бренд: Unical Страницы: 48

AAA Outdoor Boiler

Бренд: Nature's Comfort Страницы: 24

Бренд: Nature's Comfort Страницы: 25

Бренд: Ferroli Страницы: 88

INOXSTOR 200 V2

Бренд: Immergas Страницы: 16

Brava Slim HE 25 T

Бренд: Sime Страницы: 116

VC 100 (LP) COMBI

Бренд: Vesta Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды