Parts Included
A. One (1) Sliding Bin Assembly
(Slide brackets, sliding members,
slide covers and platform pre-
assembled)
B. Waste Bins (2)
C. One (1) Wire Accessory Basket
(only on single-bin models)
D. Two (2) Rear Slide Mounting
Brackets
E. Door Brackets (two pair)
F. Four (4) #6-18 x 5/8" Phillips
flathead sheet metal screws for
mounting door brackets
G. Four (4) #10-24 x 1/4" Phillips pan
head machine screws
H. Eight (8) #7 x 1/2" Phillips pan head
sheet metal screw for mounting
slide members
I. Slide Members
Tools Required
• Phillips head screwdriver
• Drill with 1/16” (1.5mm) bit for
drilling pilot holes
• Tape measure or ruler
• Pencil
• Level
Product Assemblies
TSC12-1-35 TSC15-2-35
TSC15-1-35 TSC18-2-35
TSC15-1-50
If cabinet door is attached to cabinet, remove
hinges from cabinet frame and door, and set door
aside for use in Step 6.
Mark front location for attaching slides.
On face frame cabinetry, mark 14-7/8"
(for 35 qt. applications) OR 18-15/16" (for 50 qt.
applications) up from the top edge of bottom frame
cross rail on both front frame stiles. Mark on interior
edge of frame stile. This line will indicate the slide
centerline. Using a level, verify that both marks on
cabinet frame are level. To properly locate the
cabinet member of the slide front to back and allow
for a 2mm setback, a second mark should then be
placed 1/2" back from the front of the face frame.
This mark, 1/2" back from the front edge indicates
the location of the front mounting screws for left and
right slides (figure A).
Optional Step
Using 1/16" drill bit, drill pilot holes for inserting screws.
Mark rear location for attaching slides.
On face frame cabinetry, measure 14-7/8"
(for 35 qt. applications) OR 18-15/16" (for 50 qt.
applications) up from the cabinet bottom on the
cabinet back panel. If you have a recessed cabinet
bottom that sits below the top of the bottom face
frame rail, you will need to add the amount of face
frame reveal to this number. Mark this location.
(Example: cabinet bottom is 1/4" below the top
edge of face frame = 14-7/8" + 1/4" equals 15-1/8" high mark). Using a level, verify that both
marks on cabinet back panel are level.
Determine and mark the centerline of the back panel of cabinet. Place rear bracket
installation template on back panel so that the height line on the template lines up with the
14-7/8” (for 35Q qt. applications) OR 18-15/16” (for 50 qt. applications) height line you made in
your back panel. The centerline of the rear bracket installation template must also line up with
the center line you made on the back panel of the cabinet. Tape rear bracket installation
template to back panel. Verify that the centerline and height line on template still line up with
centerline and height line on rear panel of cabinet. Refer to the chart on rear bracket
installation template to determine the distance from the centerline to the inside edge of each
slide mounting bracket for your product assembly. You will also see this same measurement in
Chart 1 below, for reference. Using a punch, mark holes for inserting screws to mount rear
bracket. Refer to template for hole locations. Remove template from rear panel. Using a 1/16”
drill bit, drill pilot holes for both the left and right rear brackets. Using two (2) #7 x ½” panhead
sheet metal screws, attach either the left of right rear bracket to rear panel of cabinet. Repeat
this process for attaching other rear bracket.
TOP-MOUNT SOFT-CLOSE
WASTE AND RECYCLING UNIT
Installation Instructions
Note: This product is designed specifically for use with traditional face frame style cabinetry. To
use with non-traditional face frame cabinetry, or Euro-style frameless cabinetry, additional
blocking may be required to provide the correct cabinet opening width.
Inspect all parts and read all instructions prior to beginning assembly and installation.
310169-B-1010
1
2700 Oak Industrial Drive NE , Grand Rapids, MI 49505 USA
800.253.1561 • 616.459.3311 • www.kv.com
Refer
to Chart
14-7/8" (35 qt.)
18-15/16" (50 qt.)
14-7/8" (35 qt.)
18-15/16" (50 qt.)
1/2"
FIGURE A
2
3
CHART 1
Product Assembly
Cabinet Opening
Distance from Centerline*
Adapter Required
TSC12-1-35
11-1/2"
4-7/16"
No
TSC12-1-35
12"
4-7/16"
Yes
TSC15-1-35
14-1/2"
5-15/16"
No
TSC15-1-35
15"
5-15/16"
Yes
TSC15-1-50
14-1/2"
5-15/16"
No
TSC15-1-50
15"
5-15/16"
Yes
TSC15-2-35
15"
6-3/16"
No
TSC18-2-35
17-1/2"
7-7/16"
No
TSC18-2-35
18"
7-7/16"
Yes
* Tolerance is +1/32" - 0"
Rear Slide
Mount
Brackets
Disconnect
Lever
Single Bin
Platform
and Basket
Double Bin
Platform
Door
Brackets
Face
Frame
Bracket
Face
Frame
Adapter
Slide
Member
Brackets
Slide
Members
