background image

Phone number: 01945 410950 

[email protected]

 

http://www.arborgardensolutions.co.uk

 

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR 

 

Nova 3 Door MDF Cupboard 400mm Wide (Nova-AGS1)

 

Before you commence the assembly process, we recommend that you read these instructions 
thoroughly beforehand to familiarise yourself with the assembly process and to also check that 
you  have  the  correct  components.  If  for  any  reason  you  need  assistance,  you  can  find  our 
contact details on the top of page of these instructions. 

 

We highly recommend that any assembly is carried out on a flat, level surface if possible 
and that you use another person to assist you if necessary. 

Also, all parts have stickers 

with part numbers attached and for your convenience all guide holes are pre-drilled.

 

 

Package contents 

2x Side panels (Part nr: AGS1_1) 
3x Partitions (Part nr: AGS1_2) 
1x Base (Part nr: AGS1_3) 
1x Back panel (Part nr: AGS1_4) 
1x Top door (Part nr: AGS1_5a) 
1x Middle door (Part nr: AGS1_5b) 
1x Bottom door (Part nr: AGS1_5c) 
3x Leg panel (Part nr: AGS_2) 
Bundle with fixings 

 

Tools required 

Electric screwdriver 
No.2 and No.3 Pozi bits 
Phillips Screwdriver 
Hammer 

 
 
 
 

 

Summary of Contents for Nova-AGS1










Reviews: