KMC Controls KMD-5210 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 38

background image



KMD–5210 Installation and Operation

Revision E

13

SECTION 2

Installation

This section provides important instructions and guidelines for
installing the KMD-5210 LAN Controller. Carefully review this
information prior to installation.

Mounting

Mount the controller inside of a metal enclosure. KMC Controls recommends
using a UL-approved Enclosed Energy Management Equipment Panel such as
a KMC model HCO–1034, HCO–1035 or HCO–1036. Insert #6 or #8 hardware
through the two mounting holes on each side of the controller to securely
fasten it to a flat surface. See

Illustration 1-2

for mounting hole

locations and dimensions. To maintain RF emission specifications, use either
shielded connecting cables or enclose all cables in conduit.

Note

Provide sufficient clearance around the controller for cables and wiring.

◆

Allow a minimum of 3 inches (7.6 cm) of clearance at the top edge of the
controller for the power and modem connectors.

◆

Allow a minimum of 1.5 inches (3.8 cm) of clearance for the ribbon cables
at the bottom of the controller.

Illustration 2-1 Mounting details

Allow 1.5 in. (3.8 cm) for cables

Allow 3.0 in. (7.6 cm) for cables

Mounting

holes

Mounting

holes

«
...
11
12
13
14
15
...
»

Содержание KMD-5210







































Отзывы:

Нет отзывов

Похожие инструкции для KMD-5210

Бренд: K&K Страницы: 6

ESSENSSE NEO COMFORT

Бренд: 2VV Страницы: 21

AirGENIO SUPERIOR

Бренд: 2VV Страницы: 27

Бренд: Bartlett Страницы: 5

Бренд: Lattice Semiconductor Страницы: 26

Бренд: Datavideo Страницы: 17

Бренд: Datamax Страницы: 22

Бренд: Ebyte Страницы: 38

Бренд: EBS Страницы: 30

Бренд: Lattice Страницы: 23

Бренд: Lattice Semiconductor Страницы: 2

Бренд: Lathem Страницы: 4

Бренд: tams elektronik Страницы: 36

Бренд: Magellan Страницы: 44

Бренд: Namron Страницы: 3

Бренд: Samson Страницы: 6

Бренд: Vaillant Страницы: 12

Бренд: ZKTeco Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды