background image

BAC-9000 Series Controller Installation Guide 

6 921-019-01F

POWER AND COMMUNICATION STATUS

The 

status LEDs

 indicate power connection and 

network communication. The descriptions below 

describe their activity during 

normal operation

 (at 

least 5 to 20 seconds 

after

 power-up/initialization 

or restart).

NOTE: 

If both the green READY LED and the 

amber COMM LED remain OFF, check 

the power and cable connections to the 

controller.

Green READY LED 

28

After controller power-up or restart is complete, 

the READY LED flashes steadily about once per 

second, indicating normal operation.

Amber (BACnet MS/TP) COMM LED 

29

During normal operation, the COMM LED 

flickers as the controller receives and passes 

the token over the BACnet MS/TP network.

When the network is 

not

 connected or 

communicating properly, the COMM LED 

flashes more slowly (about once a second).

28

29

Green ETHERNET LED 

30

NOTE: 

The Ethernet status LEDs 

indicate network connection and 

communication speed.

The green Ethernet LED stays ON when the 

controller is communicating with the network.

The green Ethernet LED is OFF when the 

(powered) controller is 

not

 communicating 

with the network.

30

31

Amber ETHERNET LED 

31

The amber Ethernet LED flashes when the 

controller is communicating with a 100BaseT 

Ethernet network.

The amber Ethernet LED remains OFF when 

the (powered) controller is communicating 

with the network at only 10 Mbps (instead of 

100 Mbps).

NOTE: 

If both the green and amber Ethernet 

LEDs remain OFF, check the power and 

network cable connections.

MS/TP NETWORK ISOLATION BULBS

32

The two 

network isolation bulbs

 

32

 serve three 

functions:

Removing the (

HPO-0055

) bulb assembly 

opens the MS/TP circuit and isolates the 

controller from the network.

If one or both bulbs are ON, the network is 

improperly phased. This means the ground 

potential of the controller is not the same 

as other controllers on the network. If 

this happens, fix the wiring. See 

Connect 

(Optional) MS/TP Network on page 5

.

If the voltage or current on the network 

exceeds safe levels, the bulbs blow, opening 

the circuit. If this happens, fix the problem and 

replace the bulb assembly.

Содержание BAC-9001










Отзывы: