background image

BAC-9000 Series Controller Installation Guide 

2 921-019-01F

NOTE: 

The drive hub and V-clamp will be 

rotated in the same direction in Step 8.

2.  Push and hold the 

gear disengagement 

lever

 

8

 on the side of the controller.

3.  Rotate the 

drive hub and V-clamp

 

9

 in the 

same direction that opened the damper.

NOTE: 

Continue to rotate the drive hub and 

V-clamp until they reach a stop.

9

8

4.  Position the controller over the 

damper 

shaft 

10

 

so that the color-coded 

terminal 

blocks

 are easy to access for wiring.

NOTE: 

The black terminals are for power. 

The green terminals are for inputs and 

outputs. The gray terminals (if present) 

are for MS/TP communication.

5.  Finger-tighten the 

V-clamp

 

nuts

 

11

 to position 

the damper shaft in the drive hub.

10

11

6.  Center the 

mounting bushing

 

12

 in the 

mounting tab

 

13

.

5

6

5.  Tighten the screw until the screw head 

touches the plastic in the bottom of the recess.

NOTE: 

Overtightening the screw can cause 

compression in the case which may 

interfere with the controller operation.

MOUNT CONTROLLER

NOTE: 

Install the controller in a metal 

enclosure for RF shielding and physical 

protection.

NOTE: 

The controller can be installed on a 

3/8–5/8 inch (9.5–16 mm) round or 

3/8–7/16 inch (99.5–11 mm) square 

damper shaft with a minimum length 

of 2 inches (51 mm).

1.  Manually rotate the 

damper shaft

 

7

 on the 

VAV box to fully open the damper.

7

Содержание BAC-9001










Отзывы: