background image

3

 

 

1.   Precaution 

1.1

 

  Safety Precaution

 

1. To prevent injury to the user or other people and property damage, the following 

instructions must be followed. 

2. Incorrect operation due to ignoring instructions will cause harm or damage. 
3. Before maintenance, please read carefully the following instructions at first.

 

 
 

1.2

       

Warning

 

 

1

. The power cord shall be replaced with

 the original power cord, 

specifications 

for an insulation power line which is no less than AWG8*2 +AWG10*1 and resists 

temperature of greater than 60

2. All apparatus within a radius of 50mm from this product must resist 

temperature of greater than 75°C, otherwise, deformations are easily to be 

caused during the application process of this product. 

3. When the wrapping materials are removed, keep such materials like metal 

sheet, packing bag, foam and screws out of reach of children’s reach to avoid 

potential dangers. For example, the children may suffocate as a result of 

swallowing tiny components or playing with packing bag. 

 

 

 

2.   Dimension 

 

 

 

 

Note: Dimensions for reference only

 

 

 

 

 

 

 

 

 

 

Model

 

W (mm)  H (mm)  D (mm) 

65L All the models

 

595 

595 

575 

Содержание EB8005ED


























Отзывы: