KitchenAid KFED500EWH03 Скачать руководство пользователя страница 13

13

Complete Installation

1. 

Check that all parts are now installed. If there is an extra 

part, go back through the steps to see which step was 

skipped.

2. 

Check that you have all of your tools.

3. 

Dispose of/recycle all packaging materials.

4. 

Check that the range is level. See the “Level Range” section.

5. 

Use a mild solution of liquid household cleaner and warm 

water to remove waxy residue caused by shipping material. 

Dry thoroughly with a soft cloth. For more information, read 

the “Range Care” section of the Use and Care Guide.

6. 

Read the range Use and Care Guide.

7. 

Plug power cord into appropriate outlet. Slide range into its 

final location. Check that the flexible conduit or power supply 

cord are not bent.

8. 

Turn power on. Turn on surface elements and oven. See 

the Use and Care Guide for specific instruction on range 

operation.

If range does not operate, check the following:

 

Household fuse is intact and tight; or circuit breaker has not 

tripped.

 

Range is plugged into a grounded outlet.

 

Electrical supply is connected.

 

See the “Troubleshooting” section in the Use and Care 

Guide.

When the range has been on for 5 minutes, check for heat. 

If range is cold, turn off the range and contact a qualified 

technician.

Moving the Range

When moving range, slide range onto cardboard or hardboard to 

avoid damaging the floor covering.

If removing the range is necessary for cleaning or maintenance:

For power supply cord-connected ranges:
1. 

Slide range forward.

2. 

Unplug the power supply cord.

3. 

Complete cleaning or maintenance.

4. 

Plug power supply cord into a grounded outlet.

5. 

Slide range back so rear range foot is under anti-tip bracket.

6. 

Refer to the “Verify Anti-Tip Bracket Is Installed and 

Engaged” section to verify engagement.

7. 

Check that range is level.

For direct-wired ranges:

1. 

Disconnect power.

2. 

Slide range forward.

3. 

Complete cleaning or maintenance.

4. 

Slide range back so rear range foot is under anti-tip bracket.

5. 

Refer to the “Verify Anti-Tip Bracket Is Installed and 

Engaged” section to verify engagement.

6. 

Check that range is level.

7. 

Reconnect power.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation 

instructions.
Slide range back so rear range foot is engaged in the 

slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed 

and engaged.
Failure to follow these instructions can result in death 

or serious burns to children and adults.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.

W10694065B

8/16

Содержание KFED500EWH03














Отзывы: