King Long XMQ6129Y series Скачать руководство пользователя страница 22

Страница: 22 / 161

Technical parameter and complete vehicle description

SI-4

Switch

Name

Color

Function

Notes

Right side bin gate

Green

Pressed on top: open the right side bin gate;
Pressed on bottom: close the right side bin
gate.

Powerful/abstemious

transfer switch

Pressed on top: turn on powerful function;
Pressed on bottom: turn off abstemious
function.

Electric sun blind

Green

Pressed on top: the sun blind getting down;
Pressed on bottom: the sun blind getting up.

Driver seat lamp switch

Green

Pressed on top: turn on the driver seat lamp;
Pressed on bottom: turn off the driver seat
lamp.

Kneeling switch

Green

Pressed on top: turn on kneeling function;
Pressed on bottom: turn off kneeling
function.

Coin box switch

Green

Pressed on top: open the coin box;
Pressed on bottom: turn off the coin box.

Turning lamp switch

Green

Pressed on top: turn on the turning lamps;
Pressed on bottom: turn off the turning
lamps.

ACU unlock switch

Green

Pressed on top: ACU unlock;
Pressed on bottom: ACU lock.

For articulate
plate only

Inner guidepost switch

Green

Pressed on top: turn on the inner guidepost;
Pressed on bottom: turn off the inner
guidepost.

Содержание XMQ6129Y series


































































































































































Результаты поиска

Содержание XMQ6129Y series

Отзывы:

Похожие инструкции для XMQ6129Y series

Бренды по названию

Популярные бренды

King Long XMQ6129Y series, Руководство по эксплуатации

Результаты поиска

Содержание XMQ6129Y series

Отзывы:

Похожие инструкции для XMQ6129Y series

Бренды по названию

Популярные бренды