King gates Star 224, Руководство пользователя

Страница: 7 / 12

9 - AUTOMATIC GATE TRAVEL LEARNING
6 7
Before the Automatic Learning!
- In this process the controller “learns” the gate’s travel time and automatically sets the default
slowdown points
- During the Automatic Learning safety devices are disabled! Keep the gate travel area clear
to prevent any damage that may be caused by crushing into an object, vehicle, person, animals...
- Ensure that the mechanical and or electrical limit switches are in-place and operating
- To stop this programming mode at any time press the SET and RADIO
buttons simultaneously.
- For systems with single motor, use MOT1 (terminal 24 and 25) and adjust
the DELAY potentiometer to (-) minimum
- For double (twin) wings, connect the motor that opens first to MOT1 (terminal 24 and 25)
- To changing the default slowdown points – see section 10
Automatic Gate Travel Learning procedure
1) Make sure that DipSwitch 2 is ON and DipSwitch 3 is OFF- step-by-step mode
2) Engage (Open) the manual override lever and move the wings to half way,
then disengage (close) the manual override
3) Press and hold the SET button for 2 seconds
- the yellow SET LED flashes
4) Immediately press the Set button again for 2 sec - gate start opening , SET LED remain
on till the end of learning
5) If the wing(s) begin moving to closing, stop the Automatic Learning process
(press the SET and RADIO simultaneously) and reveres (swap) the motor(s) wires.
Automatic Gate Travel Learning done
Advanced Programming
10 - CHANGING THE FACTORY SLOWDOWN POINTS
1) The Automatic Gate Travel Learning should be done first, the default slow down points are set at 15% of full travel
2) You may remove, or set new slowdown points
3) For new slowdown points, mark the points on the driveway
4) Make sure that the operation mode is Step By Step (DipSwitch 2 ON / 3 OFF)
5) Move the wings to half way position
6) Press the SET button for 2 seconds >> the SET LED flashes for 5 seconds
7) Press the RADIO button for 1 second >> the SET LED turns steady on and gate starts moving
8) The gate begins to open slowly, then the wings will close one after the other until fully closed
9) Press the
SET
button, or the remote control >> wings begin to open
To remove the slowdown points in opening let the wings open all the way; Or, for new slowdown point(s):
When wing 1 arrives to the new slowdown point >> press the SET button, or button 1 of the remote control
When wing 2 arrives to the new slowdown point >> press the RADIO button, or button 2 of the remote control
10) Press the SET button or the remote control >> wings begins closing
To remove slowdown points in closing let the wings to go the way;
Or, for new slowdown point(s)
:
When wing 1 arrives to the slowdown point >> press the
SET
button, or button 1 of the remote control
When wing 2 arrives to the slowdown point >> press the RADIO button, or button 2 of the remote control
ADVANCE FEATURES
14 - SAFETY DEVICES DETAILED DESCRIPTION
Crossing safety receivers
& transmitters
PHO1- SAFETY DEVICES IN CLOSING
Input PHO1 (terminal 16 and 18) is used for connecting photo-sensors as safety devices to intervene during closing.
PHO2: SAFETY DEVICES IN OPENING AND CLOSING
Input PHO2 (terminals 16 and 17) intervene both in closing and in opening
There are two options determined by DipSwitch 4 :
DipSwitch 4 ON : if trigged by safety device >> gate stops and when path is cleared keeps going
DipSwitch 4 OFF : (for Safety Edge in Opening):
Trigged in opening >> stops and closes for 2 seconds
Trigged in closing >> no effect
NOTE:
If more than one pair of photo-sensors is used, it is
recommended to have the position of the transmitters
and receivers alternated between the pair,
in order to avoid cross triggering.
SAFETY AUTO TEST
The Auto safety test is recommended in Europe. The control unit has a Safety Device Test mode
to check the operation of the devices connected to inputs PHO1 (terminals)
and PHO2 (terminals).
ENTER THE SAFETY DEVICE TEST:
1) First connect the Photo-sensor’s +VE end to the TX input (terminal 20) instead of the VA input (terminal 19),
for which it should be connected during normal operation.
2) Press the RADIO button for 2 sec >> RADIO-LED Red turns on
3) Press the SET button 4 times >> SET LED Yellow turns on
4) Wait 10 seconds >> SET LED and RADIO LED both turn off
Safety Auto Test is now activated
EXIT THE SAFETY AUTO TEST MODE (if error LED on press the SET button, and wait unit the SET LED turns off) then:
1) Press the RADIO button for 2 seconds >>SET LED and red RADIO LED both turn on
2) Press the START button once >> SET LED turns off
3) Wait 10 seconds >> RADIO LED turns off
Safety Auto Test is now deactivated
NOTE: Entering the test with the safety devices not properly connected will cause the unit to malfunction.
To determine whether the unit is in the test mode press the RADIO button for 3 seconds: if the RADIO LED turns on
then the self-test is disabled. If both the red RADIO led and the yellow SET led turn on then the test is active.
12 - RESET THE PEDESTRIAN OPENING GAP TO DEFAULT SETTING
1) Make sure that the gate is in the closed position
2) Press the SET button for 2 seconds >> SET LED begins to flash
3) Press the START button >> SET LED turns steady on
4) Press the
SET
button >>
SET LED
flashes rapidly and turns off
Pedestrian opening gap reset
13 - DELETING PEDESTRIAN ACCESS BY REMOTE CONTROL
1) Make sure that the gate is in the closed position
2) Press the SET button for 2 seconds >> SET LED begins to flash
3) Press the START button >> SET LED turns steady on
4) Press the
SET
button >>
SET LED
flashes rapidly and turns off
Pedestrian access by remote control deleted
(push button command terminal 15 still active)
11 - ADJUSTING THE PEDESTRIAN ACCESS OPENING GAP
1) Make sure that the remote control(s) is programmed for pedestrian access opening (DipSwitch 8 OFF)
2) Make sure that the gate is in the closed position
3) Press the
SET
button for 2 seconds >>
SET LED
begins to flash
4) Press the START button >> SET LED turns steady on
5) Press the START or remote or push button >> Wing 1 begins to open
6) When wing 1 arrives at the desired opening point - stop it by pressing START , remote , or push button
The new Pedestrian opening gap is set
RX TX
TX RX