Dip
01
OFF
ON
OFF - OFF
OFF - ON
ON - OFF
ON - ON
OFF
ON
02 - 03
04
A variation of the trimmer “
FOR
” (speed) requires the reset learning procedu-
re to be repeated (point 2) since the manoeuvre times vary. Decelerations
are automatically defined in the last 10% of the manoeuvre.
Power / Speed (POW):
Regulation from 50% to 100% of
the power.
Pause time (PAU):
Regulation of the pause time from
0 to 60 seconds.
Obstacle sensitivity (OBS):
Regulation of the activation time
from 0.1 to 3 seconds.
Status
Operation
5.
Yellow LED
stays on
3.
Yellow led
flashes
4.
Within 5 seconds,
press the
programming button
P1/SET
for
1 sec.
2. RESET
: press and
hold the programming
button
P1/SET
for
2 sec.
6.
The control unit
briefly open
7.
The door close until
mechanical stop
8.
The control unit
briefly open
9.
Pause for one
second
10.
The door
close until
mechanical stop.
Yellow LED switches off
END
of learning
procedure
1.
Put the door in an
intermediate position.
Flashing light fixed
Flashing light flashing
Dead man’s switch mode
Automatic closing mode
Step by step mode (Open - Stop - Close - Stop)
Step by step mode with automatic closing
Safety test disabled
Safety test enabled
PROGRAM THE TRAVEL LIMITS
SIMPLIFIED LEARNING PROCEDURE
INITIAL SETTINGS OF DIP-SWITCHES
TRIMMER
MAX
MAX
MAX
ON
1 2 3 4
For better adjustment of the obstruction control, it may be necessary (mainly with the trimmer “FOR” set at the
maximum or with heavy doors), to intervene during the opening and closing phases (points 7 - 8 - 10) by pressing the
activation key of the transmitter or the push button P1/SET on the control unit as soon as the driving carriage comes
into contact with the mechanical stop.
!
Using this procedure the installer can determine the instant in which deceleration begins and the back jump type.
PROFESSIONAL LEARNING PROCEDURE
9b.
Mechanical stop
intervenes.
End of opening
12a.
When you want to start
the slow-down, press the
start key
of a radio control
or the push button
P1/SET
8.
Do you want
deceleration during
opening?
11.
Do you want
deceleration during
closing?
9a.
When you want to start
the slow-down, press the
start key
of a radio control
or the push button
P1/SET
7.
The control unit
performs
the opening
NO
NO
YES
1.
Put the door in an
intermediate position.
Yellow led is off
2.
Press and hold
the programming button
P1/SET
for
2 sec.
Yellow led flashes
3.
Within 5 seconds, press
the programming button
P1/SET
for
1 sec.
Yellow LED turned on
4.
The control unit
briefly open
Yellow LED stays on
5.
The door close until
mechanical stop
Yellow LED stays on
6.
Press the push button
P1/SET
or the
start key
of the
radio control.
Yellow LED stays on
10.
Press the push button
P1/SET
or the
start key
of the
radio control.
Yellow LED stays on
12b.
Mechanical stop
intervenes. End of closing
Yellow LED stays on
Yellow LED stays on
Yellow LED stays on
13.
Do you
want back jump
function?
*
Yellow LED stays on
14c.
Press button
RADIO
Yellow LED turns off
14a.
Press button
START
Yellow LED turns off
14b.
Press button
SET
o r wait
8 seconds
Yellow LED turns off
YES
* back jump=
short reverse gear
at the end of the complete closing
to loosen the mechanism and
facilitate the release
NO
SHORT
LONG
Содержание ISTBJV01
