background image

ANCHORING YOUR UNIT

This canopy is designed for use as a temporary structure.  After assembly, the canopy MUST BE securely 

anchored to the ground to prevent damage from winds.  Your canopy will act like a kite in the wind if not 

properly and securely anchored to the ground.  Severe winds will cause the frame to twist and unanchored 

legs will fall, thereby collapsing the canopy.  If severe winds are expected, you must remove the cover from 

the frame to prevent damage. 

We recommend anchoring your canopy at each corner 

foot and centre foot on each side. Screw anchor into 

ground next to canopy foot using a large screw driver 

(1).  Looping  the  cable  through  the  anchor  eye  will 

keep it out of the way while turning. Tilting the anchor 

slightly  will  help  the  anchor  to  cut  into  the  ground. 

Apply  downward  pressure  while  turning  the  anchor 

into the ground. Leave approximately 8 cm (3 in.) of 

anchor out of the ground.

Slide the clamp onto cable (2). Run cable around the 

pipe, and then back through the clamp. Pull the cable 

as tight as possible through the clamp. Hold the cable 

and tighten clamp with an adjustable wrench.

When you have tightened the clamp and satisfied that 

the cable will not slip, you may tighten the cable more 

by turning the anchor further in the ground as seen in 

Diagram 1.

REUSE

REDUCE

RECYCLE

(1)

(2)

Diagram 1

Содержание StorGuard SG1324S












Отзывы: