BATTERYLESS JUMP STARTER
7
2. Bypass Operation
Note: If the Vehicle’s battery is too flat to initiate the vehicles ECU, the LCD will show the Fault / Bypass / Glow
Indicator (7) when using the weak/flat battery, please resort to Bypass Mode using the following steps.
1. Pre-Charge the Batteryless Jump Starter using a method as advised in
‘Pre-Charge Methods’ on Page 5.
2. Connect the Batteryless Jump Starter to the vehicle as shown in Fig. 7.
Disconnect the positive cable terminal from the vehicle’s battery. Attach
the Positive Battery Clamp RED (1) of the Batteryless Jump Starter to
the positive battery lead terminal of the car. ENSURE that the battery
lead can be reconnected to the battery WITH the Batteryless Jump Starter clamp still attached. (Ensure that
the battery terminal hole is not obstructed by the Positive Battery Clamp RED (1).
3. Attach the Negative Battery Clamp BLACK (2) to the negative battery terminal (or relevant negative jump
starter connection point of your vehicle)
WARNING! Ensure the Positive Battery Clamp RED (1) or vehicles
battery lead terminal does not come in contact with the vehicles body
or other metal components in the engine bay.
4. Press the ON / OFF Button (4) for approx. 2-4 seconds to activate the
Bypass Mode.
5. Start the vehicles engine.
6. As soon as the engine starts, reconnect the joined positive leads to
the positive battery terminal (Fig 8). Once on the battery terminal,
disconnect the Positive Battery Clamp RED (1) from the positive
battery lead (Fig 9)
7. Tighten the vehicles’ positive battery terminal securely.
Note: It may take up to an hour to fully charge the in vehicle flat battery
using the vehicles alternator.
•
It is suggested that you have your vehicles’ battery and charging
system checked by a mechanic or auto electrician to ensure that your vehicles charging system is functioning
correctly, or if you suspect the battery is becoming unreliable. (Any such costs associated with seeking advice
from an automotive repairer is not covered by Kincrome).
- Or recharge your vehicles battery using a battery charger compatible with your batteries ratings. Refer to the
battery chargers output ratings details to ensure it is suitable for use on your battery.
WARNING! DO NOT leave vehicles engine running with the Batteryless Jump Starter connected to the battery
after jump starting the vehicle.
3. GLOW PLUG Mode (Use on Diesel Engine Vehicles)
Generally, a diesel engine vehicle requires the glow plugs to be first energized to heat up the engine chamber before
the engine starts, as indicated by the GLOW PLUG icon on the dashboard of the diesel vehicle.
The process needs current of approx. 40-60 Amp and takes about 4-6 seconds of power
to pre-heat the GLOW PLUGS in the vehicles engine.
1.
Ensure that the Batteryless Jump Starter is fully charged and connected to the
vehicles battery, as described in Standard Operation 1.1, press the Glow Plug
Button (6), the LED Voltage Indicator (9) will display Fig 4.
2.
Turn ON the vehicles ignition to pre heat the glow plugs of the vehicles engine.
3.
After the vehicles glow plug icon extinguishes from the vehicle’s dashboard, you may now
start the vehicle’s engine, immediately disconnect the Batteryless Jump Starter from the vehicle’s battery.
Note: GLOW PLUG mode is inactive under Bypass mode.
1. Connection - for starting the engine.
Jumpstarter clamp joined to the positive
cable terminal.
2. After Jump Start- engine has started
replace the joined clamps onto the battery
3. Disconnection- With engine running and
positive cable re-connected, remove both
jump starter clamps.
RED
RED
RED
BLACK
BLACK
BLACK
1. Connection - for starting the engine.
Jumpstarter clamp joined to the positive
cable terminal.
2. After Jump Start- engine has started
replace the joined clamps onto the battery
3. Disconnection- With engine running and
positive cable re-connected, remove both
jump starter clamps.
RED
RED
RED
BLACK
BLACK
BLACK
1. Connection - for starting the engine.
Jumpstarter clamp joined to the positive
cable terminal.
2. After Jump Start- engine has started
replace the joined clamps onto the battery
3. Disconnection- With engine running and
positive cable re-connected, remove both
jump starter clamps.
RED
RED
RED
BLACK
BLACK
BLACK
Fig 7
Fig 8
Fig 9
Fig 10
