kincrome K13250, Инструкция по эксплуатации

Страница: 7 / 10

6
INDUSTRIAL RANDOM ORBITAL SANDER INDUSTRIAL RANDOM ORBITAL SANDER
4. Once you have selected the suitable abrasive disc start the random orbit sander by holding down the trigger (7) and bring the
hook & loop pad (5), slowly and evenly to the surface of the material. Moving the sanding disc back and forth overlapping the
desired area.
5. Remove the sander from the work surface before stopping the sander.
6. Note: Regularly check the hook & loop pad (5) for wear, always change a cracked or damaged disc.
7. If random orbit sander requires more power to accomplish task, ensure that the tool is receiving sufficient, un-obstructed
airflow and/or increase the speed of the sanding pad, by rotating the speed lever (4) to the left or right.
8. Increase/decrease the pressure (PSI) output of regulator ensuring you do not exceed the rated maximum inlet air pressure of
the tool (90PSI).
Caution: If tool still does not have sufficient force at maximum pressure and sufficient airflow, then a larger
tool may be required.
11) Cleaning, Maintenance, and Lubrication
Note: These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the
air-operated tool. The air motor and bearing uses compressed air to power the tool. Moisture in compressed air will rust the motor
components, you must lubricate the motor with Kincrome Air Tool Oil daily.
Cleaning
1. Regularly blow dirt and dust out of all air vents with clean, dry air at least once a week. To minimize the risk of eye injury,
always wear approved eye protection.
WARNING! Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool.
These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened only with water and mild
soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
Lubrication
Note: Remove vacuum hose (2) from vacuum port/exhaust (8) before lubricating the Random Orbital Sander.
1. Disconnect the tool from the air supply holding it so the air inlet (3) faces up.
2. Hold the trigger (7) down and put 4 to 5 drops of Kincrome Air Tool Oil in the air inlet. Holding the trigger (7) down helps
circulate oil in the motor.
3. Connect the tool to air supply, cover the vacuum port/exhaust (8) with a towel and run for a few seconds.
WARNING! Any excess oil in the motor is immediately expelled from the vacuum port/exhaust (8) .Always face the
vacuum port/exhaust (8) away from people or objects.
Storage
1. Avoid storing the tool in a location subject to high humidity. If the tool is left as it is used, the residual moisture inside the tool
can cause rust. Before storing and after operation, oil the tool and run it for a short time.
2. Regular inspection should be carried out of sanding pads, spindles, threads, and clamping devices irrespect of wear.
12) Warranty
Warranty given by Kincrome Australia Pty Ltd of 3 Lakeview Drive, Caribbean Park, Scoresby, Victoria (Tel 1300 657 528). The applicable
warranty period (24 months) commences on the date that the product is purchased. If this product has materials or workmanship
defects (other than defects caused by abnormal or non warranted use) you can, at your cost, send the product to place of purchase,
an authorised Kincrome service agent or one of Kincromes addresses for repair or replacement. Your rights under this warranty are
in addition to any other rights you have under the Australian Consumer Law or other applicable laws. Our goods come with guaran -
tees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure. For further details please visit www.kincrome.
com.au or call us. Due to minor changes in design or manufacture, the product you purchase may sometimes differ from the one shown
on the packaging.
IMPORTANT! If the tool fails to operate correctly, call customer service on 1800 657 528 for advice on the best resolution for your
situation. If a resolution cannot be achieved over the phone please take the tool and all related accessories to an authorised service
centre or place of purchase showing proof of purchase for assistance.