Kimo QM-13809S-T-20 Скачать руководство пользователя

Страница: 2 / 18

SPECIFICATIONS

MODEL

QM-13809S-T-20

Voltage

20 V

Charge Time

1-1.5 Hours

Battery Capacity

2.0 A/h

Max Keyless Chuck

0.8-10mm

No Load Speed

0-350/1350 rpm

Adjustable Torque Settings

21+1+1

G.W./N.W.

5.5 lbs / 4.8 lbs (2.5kg / 2.2kg)

Measurement

13.5

6.4

7.2 inches

•

Due to our continuing program of research and development, the specifications herein are subject to change

without notice.

•

Specifications may differ from country to country.

•

The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.

WARNING:

Only use the battery cartridges and chargers listed above.

Use of any other battery cartridges

and chargers may cause injury and/or fire.

If you have questions or comments, contact us.

[email protected]

Содержание QM-13809S-T-20



















Результаты поиска

Содержание QM-13809S-T-20

Отзывы:

Похожие инструкции для QM-13809S-T-20

Бренды по названию

Популярные бренды

Kimo QM-13809S-T-20, Инструкция по эксплуатации

Результаты поиска

Содержание QM-13809S-T-20

Отзывы:

Похожие инструкции для QM-13809S-T-20

Бренды по названию

Популярные бренды