background image

Page 2   

Kim Lighting • 16555 E. Gale Ave. • P.O. Box 60080 • City of Industry, CA 91716-0080 • 626/968-5666 • FAX 626/330-3861

Axial Flood

20 & 30 Series Mounting Options 

Installation Instructions

Surface Mount Tenon - (SMT)

The surface mount is supplied with four (4) 

K

" diameter mounting holes evenly spaced on a 5"

bolt circle diameter and 

K

" NPT tapping on side for conduit entry.  It will attach to any flat

surface.  

Mounting and strength requirements shall be engineered by others.

Installation Instructions:

Make certain the electrical supply is 

OFF 

before starting

installation.

1. Install Surface Mount in desired location.  Seal under wall 

mount as required.  Route conduit as required.  Fish wires 
through conduit system.

2. Install fixture per fixture installation instructions.

2" Pipe Tenon 

(2

C

" O.D. )

Surface Mount

Conduit System 

(By Others)

MOUNTING AND STRENGTH

REQUIREMENTS SHALL BE

ENGINEERED BY OTHERS.

!

Side Tenon Mount - STM-1A

Cast vertical slip fitter with heavy extruded side tenon 2" aluminum pipe-size tenon (2

C

" O.D. 2"

I.D.).

Installation Instructions:        

Make certain electrical supply is 

OFF

before starting installation.

1. Remove splice cover.
2. Attach side tenon mount to fixture yoke.  Square slipfitter with

fixture and tighten set screws 10 ft. lbs.

3. Pull field wires through the pole tenon and side tenon mount into

the housing.  Carefully slide the slipfitter over the tenon, making
sure wires are not pinched.

4. Square fixture with tenon and tighten (4) tenon clamp screws

progressively to 10 ft. lbs.

5.

Remove (1) side tenon mount screw, drill 

F

F

" diameter recess

in tenon for screw point and replace screw.

6. Attach fixture wires to field wired, i.e.; green-to-ground, white-to-

common, and black-to-voltage.  Replace wireway cover.

7. Install fixture per fixture installation instructions.

2" Pipe Tenon Required

(2

C

" Dia.)

Tools Required:

Drill with 

F

" Drill Bit

F

" Allen Wrench

B

" Allen Wrench

!

Splice Cover

Tool Required:

❑ 

F

" Allen Wrench

(4) 

C

"-16 

Set Screws

Cover Screw 
(1) #10-32

Содержание SM2

Страница 1: ...rength requirements shall be engineered by others Stanchion Mount Tenon SM2 The Stanchion Mount SM2 is made to be set directly into concrete Inside diameter of stanchion is 3K inches and will accommodate up to two 2 1 diameter conduits Concrete and soil engineering by others Installation Instructions Make certain the electrical is supply is OFF before starting installation 1 Dig hole to obtain des...

Страница 2: ...EERED BY OTHERS Side Tenon Mount STM 1A Cast vertical slip fitter with heavy extruded side tenon 2 aluminum pipe size tenon 2C O D 2 I D Installation Instructions Make certain electrical supply is OFF before starting installation 1 Remove splice cover 2 Attach side tenon mount to fixture yoke Square slipfitter with fixture and tighten set screws 10 ft lbs 3 Pull field wires through the pole tenon ...

Страница 3: ...l Flood 20 30 Series Mounting Options Installation Instructions 1 Fish wires by others through MTM and install MTM over tenon being careful not to pinch wires 2 Orient to desired direction and tighten 4 C 16 set screws Torque set screws to 10 foot pounds 3 To prevent windmilling remove tenon set screw drill recess in tenon for screw point and replace screw 4 Make wiring connections green to ground...

Страница 4: ...ts not in direct contact with soil shall be warranted against defects of material and or workmanship for a period of 3 years from date of sale Aluminum fixture components in direct contact with soil shall be warranted from defects of material and failure from corrosion for a period of 1 year from date of sale Limit of Liability and General Conditions Only products which are installed used and main...

Отзывы: