background image

PD05M-PCR-LE/PD05S-PCR-LE 3

Connecting PCR-LEs Together

First, connect PCR-LEs together with power signal cables. Then, 
connect the PCR-LE to the relay terminal board with output cables.

WARNING

Risk of electric shock. 

• Before you connect cables to the connectors/termi-

nals, be sure to turn the POWER switch off, and then 

remove the power plug from the outlet or turn off the 

switchboard.

• Do not use the terminal block with the terminal cover 

removed.

CAUTION

Risk of malfunction. 
• Do not reverse the L and N polarities.
• The thickness (cross-sectional area) of the output cables to 

be used for this connection should be the same as that of 

the output cables for one PCR-LE power supply.

- Note -
To acquire stable measurements, be sure to use a relay terminal 

board to connect the load. The length of the cable between the 

PCR-LE to the relay terminal board must be 1 m or less.

 

Check that the POWER switches of PCR-LEs are off.

 

With a power signal cable, connect the J2 connector 

of the master unit to the J1 connector of the slave 

unit and the J4 connector of the master unit to the J3 

connector of the slave unit.

The J1/ J2/ J3/ J4 connectors are on the rear panel
Insert the cable firmly into the connectors until the are 
locked in place.

PCR–LE

Power signal cable

Power signal cable

Power signal cable

Master unit

Slave unint

Slave unit

Example of three PCR-LEs parallel control

J2

J4

J1 J3

J2

J4

J1 J3

J2

J4

J1 J3

Locking tab

Connect for J1/ J2

connector

Connect for J3 connector

Locking tab

Connect for J4 connector

Locking tab

PCR–LE

Slave unit

Slave unit

Master unit

J2

J4

J1 J3

J2

J4

J1 J3

J2

J4

J1 J3

PCR–LE

Slave unit

Master unit

Slave unit

J2

J4

J1 J3

J2

J4

J1 J3

J2

J4

J1 J3

 

Connect all the remaining slave units in the same 

manner.

The signal flows from the J4 connector to the J3 connector 
and from the J2 connector to the J1 connector.
This completes connection.

 

Connect the PCR-LE output terminal to the relay ter-

minal board with output cables.

For detail of handling the terminal block tray, OUTPUT ter-
minal block, and load wire, see the PCR-LE series setup 
guide.
The PCR-LE Series OUTPUT terminal block is wired after 
you first pull out the terminal block tray. The terminal box 
covers ensure that you don’t touch the unwired terminals.

Bundle or twist 

two cables each.

The cable length should

be 1 m or less.

PCR–LE

OUTPUT

G N L

OUTPUT

G N L

OUTPUT

G N L

Relay terminal board

Example of the Parallel 

Connection of PCR-LE

N L

G

Содержание PCR-LE Series







Отзывы: