background image

Page 3 / 16

MD15/230-HR, MD15/230-HE, MD15/230-DA

Product Description

3.09-20.250-01-EN | 2018-08-06

Q

Item

Technical Data

MD15/230-HE Small actuator for R15xx, R20xx and RW15x 

radiator valves and other valves with an 
M30x1.5 connection that were manufactured 
by Heimeier, Honeywell-MNG, Junkers, Hon-
eywell-Baukmann, Oventrop (2001 and later) 
and Cazzaniga

MD15/230-DA Small actuator for radiator valves that were 

manufactured by Danfoss of the RA-N, RA-FN 
or RA-U series

MD15/230-HR Small actuator for valve series R15/x 

andRW15/x (manufacturer Hora, series 216Z 
and316Z) that were discontinued in 11-2015

Nominal voltage

AC 230 V ±10%; 50/60 Hz

Power consumption

Dimensioning: 4.4 VA
Nominal: MD15/230-DA  2.8 VA; MD15/230-HR  3.0 VA;
               MD15/230-HE  2.6 VA

Switch-on current

Max. 10 A for a short time

Control

Three-point signal (open/stop/close) or two-point signal (open/close)

Connection

Built-in cable: 1.5 m, 3 x 0.75 mm

2

Motor switch-off

Actuator spindle: extending = load-dependent, retracting = load-dependent

Actuating noise

<28 dB

Positioning stroke

MD15/230-HE and MD15/230-DA: 3 mm; MD15/230-HR: 9 mm

Positioning time

22 s/mm

Positioning force

MD15/230-DA nominal 100 N; MD15/230-HR nominal 240 N
MD15/230-HE nominal 140 N

Position indicator

Stroke range scale

Manual adjustment

Only when disconnected from the power supply
Socket for hexagon key on the actuator cover,
Key socket 4 mm

Permitted medium tem-
perature in valve

0..120 °C

Ambient temperature

0..50° C

Ambient humidity

During operation: 0..85 % r.h., non-condensing
Out of operation: 0..85 % r.h., non-condensing

Overvoltage category

III

Level of contamination 2
Degree of protection

IP40

Protection class

II in accordance with EN 60730

Installation position

Anywhere from vertical to horizontal

Maintenance

Maintenance-free

Weight

242 g

Содержание MD15/230-DA

















Отзывы: