KidKraft F23220 Скачать руководство пользователя страница 28

Страница: 28 / 56

Step 12: Attach Joists

Loosen the top bolt and remove the middle and bottom bolts in (2228) Wall Mount. Do not discard these

bolts, you will re-install them after the (1903) Floor Joist is attached. (fig. 12.1)

From inside of the assembly, measure 3/4” up from the bottom of (2211) Floor End and (1934) End Floor (fig.

12.2) and then attach (1903) Floor Joist to each board using the pilot holes with 2 (S4) #8 x 3” Wood Screws per

end. (fig.12.1)

Re-install the bolts in (2228) Wall Mount and tighten all three bolts. (fig. 12.1)

On the Front Wall, on both sides of (2213) Front Divider, attach 2 (2218) Short Joists to (2212) Floor Front

with 2 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut) per board. (fig. 12.1)

On the Back Wall attach (1761) Side Joist to the inside of (1894) Back Floor with 2 (H3) 1/4 x 2-1/2” Hex Bolts

(with lock washer, flat washer and t-nut) in the outside holes and 2 (S7) #12 x 2” Pan Screws in the inside holes

as shown in fig. 12.1.

Wood Parts

Hardware

4 x

1/4 x 2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

1/4 x 2-1/2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

4 x

#8 x 3” Wood Screw

2 x

#12 x 2” Pan Screw

1 x

Floor Joist 5/4 x 3 x 38-1/2”

1 x

Side Joist 2 x 2 x 34-3/4”

2 x

Short Joist 2 x 2 x 17”

1903

1761

2218

Fig. 12.1

Front Wall

2211

1903

3/4”

Back Wall

1761

1934

1903

2211

2212

2218

2228

2213

1894

x 4

Loosen this bolt

Fig. 12.2

x 4

1/4” lock

washer

1/4” flat

washer

1/4”

t-nut

Remove these

bolts

x 2

Содержание F23220

























































Результаты поиска

Содержание F23220

Отзывы:

Бренды по названию

Популярные бренды

KidKraft F23220, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F23220

Отзывы:

Бренды по названию

Популярные бренды