KidKraft CRANBROOK PLAY SYSTEM Скачать руководство пользователя страница 65

Страница: 65 / 76

Hardware

Wood Parts

From inside the fort place (2107) Door Stop against (2377) Lower Post so there is a 1” overhang and the

notched out opening is lined up with the Catch Plate then attach with 3 (S15) #8 x 1-3/4” Wood Screws. (fig. 30.4

and 30.5)

In the notched out opening of (2107) Door Stop attach the Magnetic Catch using 2 (S18) #6 x 1” Wood Screws.

(fig. 30.6)

Important: Use a hand held screw driver and DO NOT over tighten.

3 x

#8 x 1-3/4” Wood Screw

2 x

#6 x 1” Wood Screw

1 x

Door Stop 5/4 x 4 x 10”

2107

Fig. 30.4

Other Parts

1 x Magnetic Catch

Inside View

Magnetic Catch

Fig. 30.6

Fig. 30.5

2107

2377

2107

1”

S18

S15

Step 30: Attach Door to Fort

Part 2

Catch Plate

S15

S18

Inside View

Содержание CRANBROOK PLAY SYSTEM













































































Результаты поиска

Содержание CRANBROOK PLAY SYSTEM

Отзывы:

Бренды по названию

Популярные бренды

KidKraft CRANBROOK PLAY SYSTEM, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CRANBROOK PLAY SYSTEM

Отзывы:

Бренды по названию

Популярные бренды